Jump to content
SAU Community

Recommended Posts

hey im so gtst, that i wont go FMIC cause then ill need to cut my factory frontbar and lose my GTST electric spoiler :)

GTST 4 lyf :(

Thats pretty gtst :)

My efforts pale into insignificance.

I kept the povo spec gtst front bar with optional "flaking" chrome trim when the rest of the front end is gtr just so people know it's not a gtr. :D

IMG_1567.jpg

particularly important when closing the gap on 32 gtr's at the track....

Thats pretty gtst :rolleyes:

My efforts pale into insignificance.

I kept the povo spec gtst front bar with optional "flaking" chrome trim when the rest of the front end is gtr just so people know it's not a gtr. :)

IMG_1567.jpg

particularly important when closing the gap on 32 gtr's at the track....

Any more pictures? Im curious to know the proportions of the car remain with the larger front guards? Does the whole look gel

Thats pretty gtst :bunny:

My efforts pale into insignificance.

I kept the povo spec gtst front bar with optional "flaking" chrome trim when the rest of the front end is gtr just so people know it's not a gtr. :laugh:

IMG_1567.jpg

particularly important when closing the gap on 32 gtr's at the track....

Pure streeter Dave lol

Did the GTR guards bolt straight up or did you have a lot of stuffing around?

Any more pictures? Im curious to know the proportions of the car remain with the larger front guards? Does the whole look gel

It depends on the angle you look at it from :bunny:

I've flared the rears and have matching wheels all round now so it looks a lot more in proportion than it did at the time of the first photo. I'm still considering wide rear guards atm

please excuse the filth in this photo. It's seen a skidpan and a wet track day since it's last wash. And it's been raised :laugh:

post-2863-1208301901_thumb.jpg

abu, the guards bolt on, the bonnet latch and support needs changing for the bonnet swap and you need gtr indicators. The front bar doesn't quite fit right either.

abu, the guards bolt on, the bonnet latch and support needs changing for the bonnet swap and you need gtr indicators. The front bar doesn't quite fit right either.

ah thats alright

Do you know if the guards will fit with a GTST bonnet and GTR indicators?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
×
×
  • Create New...