Jump to content
SAU Community

Recommended Posts

are you planning on using bolt on guards, flares or hand flaring the guards to fit the rims?? with some stretched 245s or 255s you will come close but will still need something done... im keen to see it when your done if you are hand flaring it... thats gonna look awesome, nice wheel choice

took a couple shots this arvo and tonight, heres a few i mucked around with. Hard trying to get them looking nice without going too far :S, not sure if i did or not.

I included a few of the crappy night shots so i can get some advice :cheers:

so the night shots r shit, any tips ?? i'm pretty sure the blue spots are reflections from the HID's on the lense, hence how they can float in the sky haha.

I know i need to get a tri pod to start with for the darker shots, i didnt get a single one correctly in focus.

I also tried out my new flash tonight, nice wireless one. I tried it to the left of the car, directly infront of the car, behind the car, and at my feet, all set ups resulted in either a totally black pick (behind) a huge white spot and a shadow on the wall (to the left) an over exposed crappy look (in front) or something else, how can i correctly use this flash to better low light shots without shadows and over exposure ?. i should get a tripod for the flash too. I figure theyre generally better if you have 2 so they can correct each other ?

any tips much appreciated :D

post-22805-1226068188_thumb.jpg post-22805-1226068202_thumb.jpg post-22805-1226068215_thumb.jpg post-22805-1226068228_thumb.jpg post-22805-1226068239_thumb.jpg post-22805-1226068355_thumb.jpg

haha nice nice

How much power did you make with the RB25 turbo, heaps better to drive now?

I made 186.8kw @ 13psi. Yeah it is heaps better - Comes on a bit later than standard but makes up for it on top end as it holds 13psi and pulls till redline. It's good fun :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...