Jump to content
SAU Community

Recommended Posts

Hey guys,

Just wondering, when your intercooler pipe comes off while giving it a bit....can it cause much damage to engine/turbo/anything??

mine came off this evening, and I have never experienced it, and as I am kind of new to turbo performance, I guess you could say Im a bit nervous incase there could be damage.

Morgs who was there, says these things happen! and are normally all good, just a time hassle to get it back on.

My car has only cat back, pod and a turbotech boost controller running 9psi - could this boost controller have caused the blow out? Say a spike somewhere?

Ive taken it off and put the stock part back on just for now.

Cheers guys,

Chris

Link to comment
https://www.sau.com.au/forums/topic/120872-intercooler-pipes-blow-off/
Share on other sites

Sounds like you either don't have a good enough rolled edge/retainer on the metal pipe or your clamps were either not tight enough or not up to the job.

When the exhaust is hot you could end up with a lot of flame out the exhaust like I did, melting the rear bumper, but you have to drive a little way for that anyway. Otherwise you could just clog up your plugs with carbon but no real damage will occur if you stop pretty soon after blowing the hose.

GTRgeoff - thanks for the reply mate!

Basically I pulled into the first side street as the engine shut down, no air getting in, stalled basically.

So fingers crossed its all good!

Cheers mate,

Chris

meh don't worry it happens all the time, will probably stall pretty quickly because afm is seeing heaps of air but very little gets to the engine.. the biggest pain is getting to the lower ones under the front bar.

Some fixes:

Bigger lip on the end of the cooler pipes

New cooler hoses, preferably silicon which don't baloon out under boost

Proper truck style clamps instead of those crappy screw type ones that Nissan gave us.

Yeh ive had the same thing happen about 4 or 5 times :D still have leaking problems to. Nissan clamps suck. None of the hoses justjap gave have come off but the nissan ones will need tightening using a spanner not a screwdriver. Also i noticed that my silicon hoses went softer pretty quick so after a week or 2 u might wana retighten. About 5 of mine were loose after the first week but now they seem ok.

well,

bit of a pickle again....

this evening, noticed he car was spooling louder and earlier

(I took the turbotech b/c off, so stock boost now) came onto main road, 1st gear, changed at 2.5k, into 2nd, went to bout 3-4k and the motor shut down again, spooled really loud this time.

Something must be up with one of the rubber joints yeah?

I cant see any splits, could be underneath where I cant see?

A friend thought maybe theres an electrical fault, i.e. a sensor is stuffed?

any ideas guys?

I can drive the car, but have to keep it off boost, which is likechanging at 1k revs!!

Not good

:blush:

hhhm.... thats odd, when i fitted my cooler yesertday i noticed that there is throttle lag when you drive normally but when you punch it you dont notice anything.

my car screams now from turbo spool and induction noise but i dont think its a bad thing.

although my car does now flutter heaps, sounds like wastegate flutter to me.

hmm...apparently everything seems fine.

My mechanic tookitfor a drive and said nothing went wrong, boosted well, couldnt get it to happen!

he even sprayed some carby cleaner over the pipes, gave the car a rev, and the carby cleaner didnt get sucked in, hence no leaks anywhere...but its still got a louder, higher pitched whistle than before.

really weird.

I wouldn't worry, i helped install a front mount on my mates supra and was boost at liek 18psi when one of the hoses blew off. The car stalled and the lights even went out :( but all was good jsut some P's and Q's on the side of teh raod at night trying to get the F#&$^er back on!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...