Jump to content
SAU Community

Question About Upgrade Afms

vspecll

By vspecll,
in Engines & Forced Induction

 Share

Recommended Posts

vspecll Contributor

vspecll

Posted
Posted

Has anyone fitted Q45 airflow meters to a gtr with factory plumbing. Can it be done?

I know Z32s will stretch over the original rubber piping but I don't think Q45s will?

If you know they don't what did you use to get them to fit. I want to keep the original air box look ( it has exstensive modifing underneath) so it all looks standard and legal.

Thanks in advance.

oh, what about the wiring plug ? ( have a PFC so just have to wire up?) any diagrams out there?

:)

Link to comment
https://www.sau.com.au/forums/topic/122009-question-about-upgrade-afms/
Share on other sites
Blitz Grand Master

Blitz

Posted
Posted
or purchase Nismo AFM's.

I would never bother buying a 2nd hand AFM when new is generally only $100 more, and less hassle of a 10yr old AFM playing up

:werd:

Particularly since new Z32's have dropped to almost half the price. They used to be around $800 each new from Nissan.

Used for $300~ or new for $400~ - No brainer really.

Blitz Grand Master

Blitz

Posted
Posted
Ill be a test mule too i think for Bosch AFM's which im told are the same as Z32 :banana:

$150 new i think the price i was told... but we'll see what happens there

I dont think they are $150 Ash, but if I am wrong I will be sure to buy a few.

I have a feeling the Bosch ones are just over $300 each

R31Nismoid Grand Master

R31Nismoid

Posted
Posted
I dont think they are $150 Ash, but if I am wrong I will be sure to buy a few.

I have a feeling the Bosch ones are just over $300 each

Hrm... i think mine was special trial price :D

Im not gonna get to that for a few months, and i havent decided 100% if im going to use upgraded AFM's at all.

But the bosch stuff is only a bonus because its in the country already, and i assume some sort of manufacturing warranty etc.

Just dont anyone hold thier breath as its not gonna happen tomorrow :laugh:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...