Jump to content
SAU Community

Recommended Posts

Paint finally done.

Looks good

What size spacers are you running on the front to fill the R34 guards out? 20 or 25mm?

Also looks like you have flared the rear guards as well?

My car would have looked very similar if I decided to stay with the factory silver

Can you provide a close up pic the the bonnet hinge mounts. I need to re fab mine.

cheers mike.

I think I joined your club 'fear of speed humps and spoon drains'.

and driveways. :)

my driveway is like a speedhump and i have to be +50º from straight to get out without scraping.

at least its a 2way driveway. so i have room to swing. otherwise i'd be fkd.

Thanks for all the comments.

30mm spacer on the front and the rears were flared when I bought it but I had them reshaped a bit because they looked pretty bad.

Color looks a little darker in the flesh. It's R35 gunmetal with a little silver added to it. Close enough I didn't need to do the door sills and still look ok.

Wheels are just resprayed the original Nur spec color.

Here's the only good pic I have of the hinges. You can also see the difference in color.

3700747306_2b96131550_b.jpg

My latest purchase, crappy camera phone picture.

Would this have been on a car transporter a couple of weeks ago sporting NSW rego?

I spotted an S2 DAYZ on a truck heading south on Heaslip road a few weeks ago.

Neat ride.

:)

*EDIT*

Just noticed that it still has NSW rego in the photo

Took the bus to Prescott Hill and spent sunday going up it http://www.prescott-hillclimb.com/

The stagea at Prescott Hill on sunday

IMG_1300.jpg

5413_124879407320_672047320_2738935.jpg

Running consistent 59s/1min runs all day which i was very pleased with considering the lack of power compared to most things running up the hill and the extra weight. Need to take more brave pills for the final corner (30ft straight drop to the left) and esses

  • 2 weeks later...

Been a bit of a lurker for a few weeks, so thought it was about time to put up a pic or two of the newly aquired wagz:

2002 M35 250 RS-V (yes, the VQ25DD with 4 speed auto). Had to buy it as imo its the only decent looking M35 i had seen to that point and the Impul kit really sets it off.

3751167291_b1c60f3337_o.jpg

3751167405_94fe8eace6_o.jpg

3751956922_63db18ff9d_o.jpg

Loving it so far, just need to sort out some nice rims and i'll be done with it  :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Need to see other side of PCB in that area...ie; I don't see any thru-hole mounting, just soldered vias (smd zeners in SOT23 have 3 legs but only 2 are used, as reflected by PCB tracks)
    • 4 to 5 is fine. It will be slow, but that's better than blowing turbos. I don't have a PS pump idle up solenoid on my car, because... I think when we put the Neo in we retained my R32 lines. But.... From inspecton of the R34 vacuum hose diagram, you can see that the solenoid needs to be connected to the turbo inlet as source of clean air) and the plenum (as source of vacuum - which is the place for the air to flow to to cause the idle to increase). So 3 to 1 is VERY WRONG. 3 should go to either the turbo inlet, or the plenum. Follow the other hose from the PS solenoid and if it goes to the plenum, then your 3 goes to 2 2 would also serve as a bleed port for a boost solenoid.
    • Pull them out and pull more apart. You can't do shit with them still bolted to the floor of the car.
    • Yes it is. ZD1 is on the other side of the board. Where ZD1 is marked is clearly opposite a 2 pin device. Our 3 pin device here is not a ZD.
    • Alright, a little update on this... I called Fulcrum, who used to be the distributor in Australia. No Bueno, they don't service them anymore.  Called shock works, who don't service them but offered to dyno the shocks for performance, and suggested DNA in Sydney might service them.  Called DNA, who also do not service them and basically said they try to steer customers away from tein for this exact reason these days- there is just no support for them anymore apparently.  Both SW and DNA said they are a not necessarily a bad product, but they just don't service the brand or know anyone who does service the brand anymore.  So... I could keep calling around but at this point I think I'll probably just spring for the shockworks product, unless anyone here knows anything.  Cheers 🍻 
×
×
  • Create New...