Jump to content
SAU Community

Recommended Posts

Not all the time But When taking off in 1st or 2nd I hear a grinding noise coming from the passenger side of the engine Not sure what it is, But I know it should be there

When I turn the car on I hear like a funny knocking sound from behind the radio?? Very weird sounds like morse code.

Also Stupid question but how do u turn on and off the fog lights?

Whats the best way to brighten up the dash?? i can hardly see my revs and speedo at nite time, my old dash in the silvia was very good.

Think thats about all other then that its a 1994 R33 s1 RB25DET with about 980000 on the clock.

Edited by faz
Link to comment
https://www.sau.com.au/forums/topic/124115-just-got-my-r33/
Share on other sites

That "knocking" behind the radio sounds like a common fault in 33's which has to do with the aircon unit, do a search and it will surely come up with some results. To fix it, you need a $60 odd part and a bit of patience but it is doable

Link to comment
https://www.sau.com.au/forums/topic/124115-just-got-my-r33/#findComment-2291818
Share on other sites

If you mean clickign by knocking, it's a very common problem and apparently its a plastic cog thats had some gears sheered of it. Also i've herd to much effort to go to for fixing.

And yeah my s1 doesn't have foggies (driving lights) theres room to put them in but you will have to run wireing as i'm pritty sure there isnt' any.

Michael

Link to comment
https://www.sau.com.au/forums/topic/124115-just-got-my-r33/#findComment-2291986
Share on other sites

Re: dash lights not bright enough

I apologise if I'm stating the obvious, but R33s have a dimmer switch fitted during compliance. This means the dimmer could be hiding anywhere - have you found it and made sure it is on max?

If you have, it's fairly straightforward to remove the dash and swap the bulbs over. Most guys ditch the 3.4W stock bulbs and use 5W instead. With the dimmer in the R33s you can't go wrong. :laugh:

Link to comment
https://www.sau.com.au/forums/topic/124115-just-got-my-r33/#findComment-2292724
Share on other sites

yeah dash lights should have a dimmer switch/dial... most likely just to the right of the steering column. On some cars turning it down makes it brighter.

Foggies were an option. Some S1 have globes in em, Some don't. If you have them from factory you should have another dial right alongside your headlight dial. I dunno the technical terms :)

Link to comment
https://www.sau.com.au/forums/topic/124115-just-got-my-r33/#findComment-2292926
Share on other sites

yeah dash lights should have a dimmer switch/dial... most likely just to the right of the steering column. On some cars turning it down makes it brighter.

Foggies were an option. Some S1 have globes in em, Some don't. If you have them from factory you should have another dial right alongside your headlight dial. I dunno the technical terms :whistling:

Are you talking about the lights next to the indicators on the frontbar? My ones turn on but they're not bright enough to be foggies, I've always assumed they were extra parking lights as the ones in the headlight aren't that effective

Link to comment
https://www.sau.com.au/forums/topic/124115-just-got-my-r33/#findComment-2300868
Share on other sites

OK... series 2 SHOULD have a dimmer installed. It was required for compliance. My car has been in Australia for more than 6 years, and it has it. (funky 80's amplifier dial!)

And yes, the lights next to your indicators are your DRIVING LIGHTS... they're not called fog-lights anymore. Europeans have fog lights for... fog! And they'd be a bright yellow. Ours are just white and only light up the road immediately infront of you, and more out to the sides.

Driving lights and fog lights are weak to drive with, sure, but they are quite bright to oncoming traffic. They are supposed to be used like headlights. i.e: not in suburbian areas, and not with cars infront of you or oncoming.

Series 1's might be dimmer than series 2 though... for those s1 owners that have them.

Noone has mentioned the grinding yet, so i'll take a stab at that one. Check your engine mount on that side. If not that, check your bushes or have pedders or something check them for you. =-]

Link to comment
https://www.sau.com.au/forums/topic/124115-just-got-my-r33/#findComment-2300950
Share on other sites

And yes, the lights next to your indicators are your DRIVING LIGHTS... they're not called fog-lights anymore. Europeans have fog lights for... fog! And they'd be a bright yellow. Ours are just white and only light up the road immediately infront of you, and more out to the sides.

I wonder what the Road Traffic Act says about driving lights. From memory, the $70 fine was for using fog lights - I had a mate argue his way out of a fine when he produced the owner's manual that called them driving lights.

:)

Link to comment
https://www.sau.com.au/forums/topic/124115-just-got-my-r33/#findComment-2301325
Share on other sites

OK... series 2 SHOULD have a dimmer installed. It was required for compliance. My car has been in Australia for more than 6 years, and it has it. (funky 80's amplifier dial!)

And yes, the lights next to your indicators are your DRIVING LIGHTS... they're not called fog-lights anymore. Europeans have fog lights for... fog! And they'd be a bright yellow. Ours are just white and only light up the road immediately infront of you, and more out to the sides.

Driving lights and fog lights are weak to drive with, sure, but they are quite bright to oncoming traffic. They are supposed to be used like headlights. i.e: not in suburbian areas, and not with cars infront of you or oncoming.

Series 1's might be dimmer than series 2 though... for those s1 owners that have them.

Noone has mentioned the grinding yet, so i'll take a stab at that one. Check your engine mount on that side. If not that, check your bushes or have pedders or something check them for you. =-]

when i didn't know which places were good, i tried pedders.They knew less about skylines than the japs know about common-bogan-dores

Link to comment
https://www.sau.com.au/forums/topic/124115-just-got-my-r33/#findComment-2301875
Share on other sites

tink its another one of those some have and some dont parts. i got them on my s1 coupe, had to take to them with a saw to fit in my cooler but still work. and i have had a aftermarket dimmer switch fitted and also the park lights next to the head light were fitted for compliancing. looks like they were drilled out with a hole saw and lights fitted.

Link to comment
https://www.sau.com.au/forums/topic/124115-just-got-my-r33/#findComment-2308386
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • Bunnings would have just handed you your money back on that one!
    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...