Jump to content
SAU Community

Recommended Posts

  • Replies 178
  • Created
  • Last Reply

Top Posters In This Topic

Are you guys dieing waiting?

I'm just waiting for some of you guys to get it so I can have a look, then if they're good, i'm ordering some too.

sighs..... that means i won'tbe getting any for like 2-3 months.

Are you guys dieing waiting?

You bet, I'm going overseas for a month on 1st September, so I may not get them for some time yet :rofl:

Might have to give them a call to see if I can get them a day or two early (if they're ready)

Edited by CNR33

yeah its a bit like that isnt it..

we handed over almost 20 grand...kinda worrying but these people are very nice and i know the seat covers are high quality...

personally i dont want them to rush and compromise quality...

Now that the delivery is getting closer, what the final word on installing these. I'm pretty sure everyone will be doing the seats themselves, but what about the door trims? Are we all gonna have a go at installing these too? If not, anyone know someone who can install the door trim pieces into and R34 GT-T?

Cheers.

That's a good idea ozan. E.g. have you guys thought of techniques of how to get a good fit?

Like you know how the seats have those little adjuster knobs on the side, how do you take them off? then I'd imagine you'd have to make a small hole in the cover to put the knob back on the outside etc.

Also, found an auto trimmer here in Brisbane. They aparently do all of brisbane bmw and porsche and have worked on imports before.

Anyway I'm gonna get them out, let you all know what they are like.

Website: http://www.leebros.com.au/

Edited by OzanMakinaci

wtf? Do it yourself .... you do not have to take off the old covers - you just slip the new covers over your existing seats .... how hard can it be?

wtf? Do it yourself .... you do not have to take off the old covers - you just slip the new covers over your existing seats .... how hard can it be?

Yeah you'll find out 3-6 months down they will start to slide around and not fit properly, get it done properly the first time have it nearly as good as factory.

And yes I would rather pay to get it done properly, need to get door trims done too.

Yeah you'll find out 3-6 months down they will start to slide around and not fit properly, get it done properly the first time have it nearly as good as factory.

And yes I would rather pay to get it done properly, need to get door trims done too.

man!!!!!!! do it urself.... farrrk :)

It's a lot better when you take the old cloth off and glue the leather ones on.

that sounds like a good idea. anyone obtained quotes to get this done professionally?

IMO, it's not worth it.

The idea of these seat covers being that the price is moderately less than a proper leather retrim.

If you've gone for the premium package - 630 + 3-400 to install it, then that's 1k. I know it's still less than a leather retrim, but at the end of the day, they'll never be as good as a leather retrim for 2 main reasons:

1. they're plastic.

2. leather retrims sew pockets into the back of the leather, and they refit the metal rods that are in the stock seat covers. They use hog rings all over the seats and velcro such that it actually hugs the contours of the seats.

have you noticed in the pics that these covers are just limp?

Manwhore, i suppose you might be able to glue it, but it'll mean that the covers can never be changed otherwise the foam will be damaged.

I have friends involved in retrimming and they suggested i just do it myself as the outcome will be the same for those reasons mentioned above.

Oh man, if you wanted a professionally installed leather interior, then you should have gone to a trimmer, these are seat covers and are therefore meant to be slipped over the origional seat trims for a good fit, unless you dont take care of them or put them on properly the first time then you wont have any problems with them.

As for door trims, they are easy as to install, man if someone wants me to install them in sydney then let me know, i custom cut, glued and made my red italian leather door trims and they look awesome! just got a few pointers from a mate that did his interior in vynal and i was off.. no problems at all....

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • 12+ months passed so they have no obligation to do a warranty claim. It leaked from the rear circuit. Front circuit was fine, but I tried many times to bench-bleed and in-car bleed (wasted 1L of Penrite racing brake fluid) to no avail. Threw my old BM50 or whatever the standard R32 GT-R BMC is, brakes went back to normal. So from my very limited anecdotal experience, I cannot recommend HFM, even though a lot of their products looks good. Just my experience (I have a genuine Nissan BM57 in a box waiting to be installed now).
    • How dare you sell your unreliable Skyline and buy a reliable, Toyota/Yamaha car with a strong gearbox, torsen LSD and Toyota reliability. At least you won't need to worry about oil pumps, big catch can, oil restrictors, blowing off power steering belts, sheering off 3rd gear, failing ABS relays/pumps, etc.
    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
×
×
  • Create New...