Jump to content
SAU Community

Recommended Posts

was out in braddon last night and only saw 1 other skyline ... was a grey 32GTR which I pulled up to at the lights and asked if he knew where the rest of the skyline bunch meet up but he had no idea...

where u guys meet ?

was out in braddon last night and only saw 1 other skyline ... was a grey 32GTR which I pulled up to at the lights and asked if he knew where the rest of the skyline bunch meet up but he had no idea...

where u guys meet ?

Grevelliea park boat ramp where auto italia used to be. if you head towards the airport (away from civic) down moreshead drive turn right at the first roundabout after the kings avenue/russell roundabout

ahhhh.... i went for a spin on friday night around civic and by passed the NMA though it was 10pm and couldnt see any skylines around - no i know why.... lol...

cant make this friday but im keen next friday to meet everyone!!!!!! well at least some of you!!

ahhhh.... i went for a spin on friday night around civic and by passed the NMA though it was 10pm and couldnt see any skylines around - no i know why.... lol...

cant make this friday but im keen next friday to meet everyone!!!!!! well at least some of you!!

what don't want to meet everyone? and are you going to take your new baby to the skid pan?

guys im out to meet this friday night i just need the exact street this place is at... and ill put it in my gps and ill be there!! woo so stoked!

regoregorego!

grevelliea park off moreshead drive.. its a car park so i dont think there is a street address.

if you read my above post its really not that hard to find

Hey Rev Head88 (kyle) ,

I live in Ngunnawal I can meet you in dickson and we can cruise to the meet spot if ya want ...

that would be awesome!! what time say 9.00pm???

in woolies carpark??

wb this arvo so if i kno im meeting you there.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...