Jump to content
SAU Community

Recommended Posts

just so u know its 45 from center of car at 20 m

ive been done for this

it realy comes down to the cops descresion and the relaility is u just pay the $90 fin and move on

Yeah - neo32 is on the money... 45 degrees is the rule.

As for the previous post about the distance being 45 metres... I think I would need binoculars to see it from that far away even at 90 degrees :angry:

... Spose, my eyesight isn't that great though, LOL.

it can be a $340 fine and 3 points if u own the car

it was the first day those red monaros were on patrol and i got done buy one bullshit situation she only saw the front of the car for 3 sec and then follewed me for 15 mins then pulled me up for it i protested it they came out and measured it and i was there when they did definatly 45 deg and 20 m

they had the speed gue and everything the thing is tho on one side of the car it angles away so from the far side away from the plate its imposable to read if its screwed onto the car if the plate was straight faceing froward no on the angle with bar it would be ok

I didnt think you had to display a front number plate?

Im pretty sure by law your not required to, but if they pull you up on that and you show them the legislation in writing, they are going to rape you for as much other stuff as they can.

Why not save the $90 or $340 and just leave it where it is, the middle.

If you have a modified / aftermarket front bar, it may not be practical to leave it in the middle. Plus the intercooler gets more air if the plate is offset. But as long as it can be viewed from the said angle / distance, then you should not get a fine anyway.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...