Jump to content
SAU Community

Qld Licence Plate Positioning

Rossman

By Rossman,
in Queensland

 Share

Recommended Posts

17SOK Collaborator

17SOK

Posted
Posted
just so u know its 45 from center of car at 20 m

ive been done for this

it realy comes down to the cops descresion and the relaility is u just pay the $90 fin and move on

Yeah - neo32 is on the money... 45 degrees is the rule.

As for the previous post about the distance being 45 metres... I think I would need binoculars to see it from that far away even at 90 degrees :angry:

... Spose, my eyesight isn't that great though, LOL.

neo32 Experienced

neo32

Posted
Posted

it can be a $340 fine and 3 points if u own the car

it was the first day those red monaros were on patrol and i got done buy one bullshit situation she only saw the front of the car for 3 sec and then follewed me for 15 mins then pulled me up for it i protested it they came out and measured it and i was there when they did definatly 45 deg and 20 m

they had the speed gue and everything the thing is tho on one side of the car it angles away so from the far side away from the plate its imposable to read if its screwed onto the car if the plate was straight faceing froward no on the angle with bar it would be ok

hayden49 Rising Star

hayden49

Posted
Posted

I didnt think you had to display a front number plate?

Im pretty sure by law your not required to, but if they pull you up on that and you show them the legislation in writing, they are going to rape you for as much other stuff as they can.

Thunderbolt Rising Star

Thunderbolt

Posted
Posted
Why not save the $90 or $340 and just leave it where it is, the middle.

If you have a modified / aftermarket front bar, it may not be practical to leave it in the middle. Plus the intercooler gets more air if the plate is offset. But as long as it can be viewed from the said angle / distance, then you should not get a fine anyway.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Boost cut after swap(RB25DET NEO) R34

      By Kinkstaah · Posted

      Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • Duncan
      V37 Radiator removal

      By Duncan · Posted

      So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Duncan
      V37 Radiator removal

      By Duncan · Posted

      Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • Duncan
      V37 Radiator removal

      By Duncan · Posted

      OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
×
×
  • Create New...