Jump to content
SAU Community

Recommended Posts

  • Replies 219
  • Created
  • Last Reply

Top Posters In This Topic

  stasis said:
so had the cam gears being dispatched out yet?

Yes, most, just be patient, like i said all will be recieved no later than early next week.

I have to jugle work and this.

thanks bnuddy!

got my cam gear today!

sorry about the post i made a few days ago.

im as happy as larry now!

and people to assure you, they are of very high manufacturing quality!

im very pleased with the cam gear in (blue) that i received, i will keep you posted as to how this cam gear tunes up!

im hoping it will be fine! looks good to me! but we will find out in the next few weeks i guess! dyno rebroad minded persons will prove it or not!

im hoping this will give me another 20rwkw - thats the plan anyway!

so im hoping for a lazy 220rwkw - power fc, pump, 14psi, dump + 3inch exhaust, FMIC, filter, fuel pressure reg!

thats the plan!!

thanks again r33kid, very happy with the product!

cheers

Giffo

just one query, i wont be posting anymore about when its arriving or whateva,

but are these being sent by courier, cause if they are then they wont send to my post box, as i have found out with other stuff.

if not shes all sweet,

please let me know if its courier

Got mine today as well, took me no more than 2 hours to get them on, set it +3 inlet, -5 exhaust (crank), noticable difference seat of the pants, will get on a dyno next week.

  siddr20 said:
kjb_r33 -- you in sydney??

Which car did you install this into.. hope the car with an rb25 in it lol..

What should my settings be??

Yeah, penrith, was a 32 with a rb20

  Munna1 said:
Will be worth while for the cost but as you obviously have a upgraded turbo a set of tomei poncams would give you better gains. but this would be a lot more expensive than a cam gear.

cheers

So whats the difference between gains with either an exhaust camgear and poncams?

Whats better on spending money on?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...