Jump to content
SAU Community

Recommended Posts

Looks like the japs are starting to Join the GTR drag scene again. Us aussies and kiwi neighbours might have gotten them a bit cautious to the times a lot of our GTR's have layed multiple nines eights and a seven. :wave:

Us aussies and kiwi neighbours might have gotten them a bit cautious to the times a lot of our GTR's have layed multiple nines eights and a seven. :wave:

which aussie GTR has run a 7?

NXTTIME see the first pick buddy.:(

recently ran in england with english driver fisrt time for him using a hks air shift box first time out at santa pod went 8.2@168mph car is going to malaysia next. i have pics but will put more later.

these 2 pics

time slip in england

and launching in japan (7sec run) :D

post-7189-1153488683.jpg

post-7189-1153488730.jpg

Edited by nismo 400 R N1
NXTTIME see the first pick buddy.:wave:

recently ran in england with english driver fisrt time for him using a hks air shift box first time out at santa pod went 8.2@168mph car is going to malaysia next. i have pics but will put more later.

these 2 pics

time slip in england

and launching in japan (7sec run) :D

Thanks Nismo. I must have missed it the first time :O Nice work.

hold me to it all you like, an quad rotor or even a 20b in a full tube chassis car have struggled in the past getting into the 6 sec time zone and these are full on race cars, fiberglass everything and again TUBE CHASSIS. I stand by it till the dying day you will never see a full bodied GTR ( ie standard sus, body parts etc) with 4wd and a rb26 run a six!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...