Jump to content
SAU Community

Recommended Posts

Looks like the japs are starting to Join the GTR drag scene again. Us aussies and kiwi neighbours might have gotten them a bit cautious to the times a lot of our GTR's have layed multiple nines eights and a seven. :wave:

Us aussies and kiwi neighbours might have gotten them a bit cautious to the times a lot of our GTR's have layed multiple nines eights and a seven. :wave:

which aussie GTR has run a 7?

NXTTIME see the first pick buddy.:(

recently ran in england with english driver fisrt time for him using a hks air shift box first time out at santa pod went 8.2@168mph car is going to malaysia next. i have pics but will put more later.

these 2 pics

time slip in england

and launching in japan (7sec run) :D

post-7189-1153488683.jpg

post-7189-1153488730.jpg

Edited by nismo 400 R N1
NXTTIME see the first pick buddy.:wave:

recently ran in england with english driver fisrt time for him using a hks air shift box first time out at santa pod went 8.2@168mph car is going to malaysia next. i have pics but will put more later.

these 2 pics

time slip in england

and launching in japan (7sec run) :D

Thanks Nismo. I must have missed it the first time :O Nice work.

hold me to it all you like, an quad rotor or even a 20b in a full tube chassis car have struggled in the past getting into the 6 sec time zone and these are full on race cars, fiberglass everything and again TUBE CHASSIS. I stand by it till the dying day you will never see a full bodied GTR ( ie standard sus, body parts etc) with 4wd and a rb26 run a six!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...