Jump to content
SAU Community

Recommended Posts

  • Replies 112
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

nah it sounds about right, the rev limit is at 7000 but what the ecu see and what the tacho see are two different things. it probably did reach 7800 at once stage, if you just keep bouncing and trying to make it, it will probably get there. i also get 3 different rev and speed settings from hand controller, rsm and stock tacho and speedo

I got about the same k's as you paul. I filled up in hoppers before i left on sat morning n got 200k's n used 1/4 of a tank when we got into shep, then had half a tank left after D4D and got home just under 1/4 left and had done 430k's so i would have gotten around the same as u easy.

For sure mate! It'll be great to see the old holden sideways. Just make sure it's got a locked diff and you'll enjoy yourself. Just do it for the fun of it, because your car will be the limiting factor. Give it a go!

haha, ya the car is gonna be a big factor in being gay, altho will be out there to have a ball, not to compete, its all about the fun, and socialising etc :)

its got a fkn tite assed mechanical lsd in er, recently rebuild n shit ... its nice :wave:

mite take a while, damn money holding me back !!!

Go the Lada!! :D

ladaburnoutrf6.jpg

So who photoshopped the smoke in there :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...