Jump to content
SAU Community

Recommended Posts

hi guys just got home, picked up the cat and pipe from the GPO and the guy was like thank god its taking up a whole shelf lol. then he picked it up, aimed it and yelled BAZOOKA!

cheery faces all round thanks heaps it looks absolutely awesome a fair bit of work by the looks of things. hope it fits easy

thanks again

  • Replies 91
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

got mine yesterday...

didn't come by registered though just normal post.. not that i care because it arrived :D

having it installed friday hopefully...

will let eveyone know a comparison to how it was with the 3" bellmouth previously

got mine on last night. lined up perfect thanks again mic. got a nice whistle note to the exhaust now and got an extra 1.1 psi boost increase when running 9 psi. used to peak at 8.8 now at 9.9 psi so be carefull if your running higher boost :D

got mine fitted today, sounds a lil louder than usual, thou i dont have a cat back yet...

The dude charged me 190 bucks, i think i was ripped off badly, oh well its on now, he had to add like another inch of pipe cause it wasnt fully connected up, so i donno how that works out... Neways still very happy with it and it looks great!

maybe coz you got a 4 door car, so the lenght of the exhaust should be longer?? to connect to the cat??

Hmm 190 seems ok.. If the bolts snapped off or something then they charge more. its basically all labour. Took me 3 hours or so.. Or i think it was 4..

But still need to take it out again and heat wrap it..

What do u guys use to heat wrap it?

I was just about to bring this up - have people done it or not?

went down to autobarn and they sell some - looked a little dodgy though and $20 for like ~5m. Is it really needed as Ill Ive heatwraped up id the larger of the spilt pipe all the way down to where the smaller pipe joins the bigger one.

So should I spend another 20 and get it all wrapped up?

yeh i think it is cause i got a 4 door, the length would be a tad longer... but yeh i suppose i have no complaints over the installation, better payin a lil more for it to be working fine than paying less for it to stuff up

Well depends if you need to heat wrap it..

Mine is touching the aircon pipe.. The aircon pipe contains gases. SO think about. The pipe touch the aircon pipe in summer with high temps for long periods of time. Sooner or later its just gonna melt that pipe or make a hole. I will leave the rest to your imagination.

But if your wastegate pipe (the smaller pipe) doesnt touch the aircon pipe then it should be fine i guess..

Should be about 50 bucks for a decent quailty one tho.. Any exhaust shops should have them.

Im gonna heat wrap mine up b4 summer really hits. So most likley mid sept. Or i might have to relocate that air-con pipe.

Keep you posted i guess when i get mine done.

Edited by siddr20

Got mine fitted today, car is alot more responsive to say and the topend has picked up quite abit too.

Just wondering though: did anybody else have their wastegate split pipe VERY close to the gearbox? Mine is actually TOUCHING at the moment but the dump flange lines up with the turbine perfectly. Theres no rattles and bangs when driving at all, but I'm still abit paranoid - can anybody confirm this is ok? Michael?

Thanks,

Andy

got mine fitted yesterday

previously i had the 3" bellmouth and ran 14psi to make 155rwkw

with the 3" split, i ran 13psi to make 170rwkw :rolleyes:

that's 15rwkw at 1psi less! dyno graphs to prove if anyone needs...

oh, and the split pipe runs on the opposite side to the gearbox on the rb20.. mine almost touches some aircon lines but they are insulated so its all ok..

OnGsTa,

Check the pipe to see if it has any indentations at the point that its touching. it will most likely not be a problem because the R34 dump & front pipe is bolted not only at the turbo flange but also has a bracket that that gets bolted to the car just before the cat, so there will be no movement/friction against the box.

WazR32GTSt,

Thats a great difference! Thank you for sharing that information :rolleyes:

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...