Jump to content
SAU Community

Recommended Posts

THIS IS NOT FOR A SKYLINE:

I need to borrow 4 rims and tires for a Mitsubishi Lancer. The ones that came with the car put the track off by 20mm, and also didnt have the right load rating (only 500kg not 530).

I borrowed a set off a mate of mine, but they didn't pass either, the rolling diameter was out... (They were 70s i need 65s).

This is what i am after, either to borrow stock MR lancer mags (most idea option but they must be the STOCK ones, and have the correct tire width and height), or else the specific ones on the tire placard:

185/65R14's with a load rating no less than 86 (530kg), and a speed rating of no less than H. The rim size is 5.5J.

Please get back to me asap if can help me out. THANKS!

Any one? Need to sort this out by the end of this week!

Yeah, tis a bit of a bitch, no wreckers have them, nor ezy scrap. I wish i knew some one with one, but dont atm...

The ones i borrowed from a mate had the 70's not 65's so didnt pass...

Looks like we may have to buy 4 crap cheap arse tires for this.....

Ended up buying some second hand ones with bout 90% tread for $55 a corner. bit better than $71-75 for the cheapest new ones.... Will have to do, and when we can afford it, will get nicer rims and tires for the car again.

Pack it with foam or some shit haha

I was told to put some metal flyscreen gauze stuff in the pipe somewhere where it can't be seen by inspectors and that should help muffle it more.

Just DON'T Flogggg the Carp out of it !

yes I said carp. :thumbsup: Here fishy fishy fishy...

The metal flyscreening is best and as long as dont flog it then it will not be an issue, and it is easy to clean out and remove after.

The other thing you can use is the big loop sturdy steel wool. We used that stuff in our motorbike at home for years so as not to piss off the neighbours when we road it around the yard as kids.

  • 4 weeks later...

Heya everyone!

So I had a preemptive check done on my car for rego.

Got the over 9000 window tint removed but now I need a set of stock r34 wheels with good tread (apparently my wheels are too wide) and a stock exhaust or a quieter cannon I could buy off someone.

If anyone wants to help me out I can repay you with you favorite beverage or swing a few spendoolies your way.

So glad I got a week long permit and not just a day long one.

Wicked! I'm just going to see tomorrow if an exhaust shop can just chuck a resonator in my current system because I know one has been taken out but if I can't get that done in time...

Hey guys,

did not even notice this thread!

Does anyone have a stock or quiet catback exhaust for an R32 GTS/GTST that me and my dad could borrow for his car to pass roadworthy? We tried the steel wool trick and it still failed :down:

Cheers!

Hey all, I had some stock wheels sorted but the guy will be away on my days off (tomorrow and thursday) Does anyone happen to have a set of stock r34 rims they could swap for mine while i get my rego check?

cheers,

Andy B

Hey guys does anyone have a torque wrench I can borrow on the weekend? Me and dad are swapping the whole from suspension/hub assembly on his 32 and looking at the service manual we're gonna need a torque wrench lol.

Cheers,

Drew

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Let me assume that the concern over a manual ECU is that the NeoDET that you have was an auto and has an auto ECU. That ECU will not be a problem, but you WILL have to Nistune it. And you would have to Nistune it even if you had a manual ECU, because the turbo ECUs will shit the bed if they do not have all the things that they were told they have to have, to be happy. The big one being the TCS CU, which you won't have in your car. Anyway, with an auto ECU (which I have running my originally auto NeoDET in an R32) Nistune allows you to put in a Stagea image which doesn't panic about the absent TCS, and allows you to override a whle bunch of other annoyances that would otherwise see the check engine light on 100% of the time. Also, you can't wind up the power very far on the stock NeoDET ECUs without Nistune, because the boost sensor gets in the way. Nistune allows you to push that problem much further up the dial. Do you even have the boost sensor with the engine? Without it, you are SOL and will need an aftermarket ECU (or to find a sensor somewhere, god knows where). I can't tell you what the wiring loom differences are in a 34. But what Duncan said above needs to be considered. When you say "loom", does that include the transmission loom? Because you will need to swap out the auto tranny loom for the equivalent manual loom, and get rid of the neutral/park start interlock (basically hot wire it).
    • I have had the r3c in for years now, maybe close to 7 years and it has never missed a beat, anyone can drive it. Super easy to drive around town, the hotter it gets does get a little hard but it holds the power easy as 
    • Shit thing to find eh? I guess the big issue is that whatever "fix" you do now, it might slow the rust down but won't fix it. I just wanted to add that in no way is fixing sheet metal in 3 dimensions the place to start with welding....that is a pro only job because its too hard to work out where things should be, let alone doing a clean enough job that it can look OK and still be strong too.  I needed to get a new rear quarter panel on the GTR and it took a pro weeks to get the old one off cleanly, new one on in the right place and looking somewhat like it should have with most of the previous connecting panels in place. Gluing a couple of bits of metal together with a welder in the garage is doable, but that is totally different to doing panel  replacement
    • This seems to be a very popular swap since all the turbo skyline prices went through the roof! I'll let someone more familiar chime in, but I understand that yes you probably want to swap the loom in to swap out the auto TCM stuff. You should not assume everything just plugs in either, you need to check at least the ECU wiring diagram for any differences at the plug at the left headlight and probably the ones near the ECU that join the dash loom too  
    • hows it fellas, my first post here which seems crazy cos half the forums i read are like the same age as me haha. to make a long story short ive got an r34 sedan (rb25de neo auto) which im swapping to a s0/s1? rb25det, r33 big box and nismo gt pro lsd. i have the motor and gearbox all bolted up outside the car, old motor and trans out. i bought the motor with stock ecu and loom, do i switch over to that? or will it be easier to get a r34 manual ecu and keep the loom if thats even possible.  also engine mounts look different, anything else thats different or incompatible? cheers, hope this all makes sense Paddy
×
×
  • Create New...