Jump to content
SAU Community

Reset Ecu Procedure

Cyprus

By Cyprus,
in Engines & Forced Induction

 Share

Recommended Posts

GtstCoupe Proficient

GtstCoupe

Posted
Posted

Ok very easy, disconnect you battery negative will do

and leave the door open so that the light is on and once you

take the neg. off the batt go and pump the brake

a fewtimes or just try to turn sumstuff on like centrallocking etc

just to drain allthepower from the caps in theecu and in the car and

then give it a fewminutes and simply re-connect and start car, go for a drive and alldone. :-)

217/r33 Community Regular

217/r33

Posted
Posted

Ok I just so don't believe in that method

1* Remove fuse panel on driver side

2* Locate the plug like in the picture below

3* Find a paper clip, Turn on the reds (don't start) Short circuit the 2 wires for 2 seconds. (WIRE COLOURED BLUE/BROWN)

Your ECU is now reset and in diagnostic mode. If you get 5 fast flash's and 5 slow flash's with your engine light all you sensors are fine. If not refer to the code list below. AND YOUR DONE !... With no stupid battery terminal removal.

Cheers,

Alex...

Ok very easy, disconnect you battery negative will do

and leave the door open so that the light is on and once you

take the neg. off the batt go and pump the brake

a fewtimes or just try to turn sumstuff on like centrallocking etc

just to drain allthepower from the caps in theecu and in the car and

then give it a fewminutes and simply re-connect and start car, go for a drive and alldone. :-)

  • Like 1
rob82 Mentor

rob82

Posted
Posted
i want to reset my stock ecu in my Series II r33 Gts-t so it learns that i have changed my dump pipe / front pipe / & cat back .. and upgraded smic ..

how do i do it and what is the procedure step by step?

plz help .. much appreciation

Nissans have no LTFT (long term fuel trim) capability, they are a dynamic system so only STFT (short term fuel trims) are learnt which means every time you power off it loses any of the changes it may have learnt. So in doing a reset it will do sweet f**k all in terms of fuel metering and most likely do nothing at all with ignition - but feel free to reset maybe it will fix you big end knock!!!

  • 4 months later...
O.I.C Napster Collaborator

O.I.C Napster

Posted
Posted
Nissans have no LTFT (long term fuel trim) capability, they are a dynamic system so only STFT (short term fuel trims) are learnt which means every time you power off it loses any of the changes it may have learnt. So in doing a reset it will do sweet f**k all in terms of fuel metering and most likely do nothing at all with ignition - but feel free to reset maybe it will fix you big end knock!!!

Ok now im confused, does anyone have proof or anything saying that disconnecting the battery or shorting out the fuse thing actually reset the ecu?

i know its a long thread that people have been reading but does any of these actually work?

I aint no mechanic but yeah im sure more then just me would like to know.

Cheers M

fr0st Experienced

fr0st

Posted
Posted
Ok now im confused, does anyone have proof or anything saying that disconnecting the battery or shorting out the fuse thing actually reset the ecu?

The ecu contains form of memory that retains its state after the power is removed. No flash, no eeprom. There is no possible way it can store fuel trim maps between drives without constant power, which I'm quite sure that it doesn't because power is removed when the car is switched off.

I'd be looking elsewhere for your problem if you have one

TSL Enthusiast

TSL

Posted
Posted
There is no possible way it can store fuel trim maps between drives without constant power, which I'm quite sure that it doesn't because power is removed when the car is switched off.

Nissan ecu's do have a constant power feed direct from the battery.

I think people are grossly overestimating the capabilities of the ecu's self learning.

SKY 34 Mentor

SKY 34

Posted
Posted
The ecu contains form of memory that retains its state after the power is removed. No flash, no eeprom. There is no possible way it can store fuel trim maps between drives without constant power, which I'm quite sure that it doesn't because power is removed when the car is switched off.

I'd be looking elsewhere for your problem if you have one

power still flows even after you switch off the car, that is why if you leave your car battry in without switching on the car for a month or so the battery will be drained

although how does resetting the ecu makes it re-learn? I think the ecu will retain its memory, just like your computer, you switch it off, pull the plugs, you don't find all your data lost..

if the ECU has self learning and STFT, wouldn't fitting the exhaust system automatically be recognised? so why bother to re-set?

Munkyb0y Grand Master

Munkyb0y

Posted
Posted
Nissans have no LTFT (long term fuel trim) capability, they are a dynamic system so only STFT (short term fuel trims) are learnt which means every time you power off it loses any of the changes it may have learnt. So in doing a reset it will do sweet f**k all in terms of fuel metering and most likely do nothing at all with ignition - but feel free to reset maybe it will fix you big end knock!!!

^^^

that's what i've been told by a couple of tuners.

apparently, any learning that may occur will basically happen each time you start the car, although it's minimal to none. The ecu just isnt that smart.

  • 5 years later...
Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

Nissans have no LTFT (long term fuel trim) capability, they are a dynamic system so only STFT (short term fuel trims) are learnt which means every time you power off it loses any of the changes it may have learnt. So in doing a reset it will do sweet f**k all in terms of fuel metering and most likely do nothing at all with ignition - but feel free to reset maybe it will fix you big end knock!!!

I was under that impression too, it is a closed loop system and changes dynamically to achieve stoich. Timing is a fixed map and only retards on knock detection.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sinn3r
      R34 Skyline climate control unit transistor

      By sinn3r · Posted

      You can’t see much on the other side as the lcd is there I don’t think it’s the same as the m33 beside it as the markings on top is not the same was hoping someone had a good quality photo or if they just happened to have the unit in hand, quickly take the cover off and take a photo to clearly show the marking on top to identify the diode   the unit is currently with an electronics repair shop so I can’t take another photo at the moment hopefully they are smart enough to know if it’s a zener diode or not
    • soviet_merlin
      WGNC34 - floor mats

      By soviet_merlin · Posted

      I'd be very surprised if you can buy new OEM mats. But if you can, I want some too!  Do you have links to the variations you found? Also, where are you located? I found that Nengun is happy to list items to purchase but when you do buy them you'll get an email that it's actually discontinued. As far as I know the variations in floor mats are different colour schemes as well as automatic and manual having a slightly different shape. The automatic ones fit into a manual car without issues, but I think you'd have trouble fitting the other way around. I have photos that show the shape difference if you care. FWIW I bought sets of used floor mats in decent condition at yahoo auctions.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Marek
      Hi everyone.

      By Marek · Posted

      Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
×
×
  • Create New...