Jump to content
SAU Community

Recommended Posts

I can't remember if I have already posted some pics up of mine but here they are anyway.

Hey Neil, how low is your car? Do you have scrubbing issues? What are sizes of your rims and what suspensions are you running? The reason I ask is that I have had my suspension raised slightly since these pics were taken to avoid scrubbing although my rims are 19X9 front and 19X10 rear which makes it slightly tricky but you have the stance that I am after. The pics you have taken look great. Feel free to come and take photos of my car anytime :sorcerer:

post-29193-1201072145_thumb.jpg post-29193-1201072161_thumb.jpg

post-29193-1201072190_thumb.jpg post-29193-1201072208_thumb.jpg post-29193-1201072352_thumb.jpg

Neil and swink your cars are so nice!

Neil - where do you get those wheels from :) i havent seen them before :)

Straight from Japan! :) I have been told they were a limited run of 3 piece LE37's from Volk.

I could be completely wrong though... :)

Neil

the side skirts i think are m spec ones i dunno much bout skylines as this is my first one, but a mate has a 94 mspec but the side skirts are different so buggered if i know lol and the wing wouldnt have the faintest idea, its got some lil cracks in the corner of it. i wanna get rid of it and puut the dwing or seriers 2 wing on it. ne ideas on wat wing would suit it??

im heading off to go camping at apollo bay tonight just to take pics, wif a my white r33 and a mates white r33 and another black r33 will be taking a few pics tomorrow will post them wen i get back tomorrow night. should be good.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...