Jump to content
SAU Community

Is This Safe?

LiQuid IcE

By LiQuid IcE,
in Victoria

 Share

Recommended Posts

LiQuid IcE Experienced

LiQuid IcE

Posted
Posted

Hey this may sound like a dumb question and NO I haven't tried it yet but....

Installed a HKS evc the other week and need to calibrate it.

Don't have anywhere I can boot the car to do this, and don't wanna do it on the street ....so was wonderring if it is safe for me to jack the car up, put it on stands and drive it. (Like an excersise bike:) )

Or do I risk the car jumping off the stands or something worse?

It actually sounds quite stupid to me but was wonderring if its possible?

Thanks!

Link to comment
https://www.sau.com.au/forums/topic/130556-is-this-safe/
Share on other sites
paulr33 Grand Master

paulr33

Posted
Posted

its not safe and even if you did it, its not accurate. the road will give different load rating and affect how the solenoid will turn on and off. just do the self learn in a quiet street or private road somewhere.

youll need about 100meters odd to do it, so it should be fairly easy. sit in 3rd gear. take off in 3rd (youll have to ride the clutch) then full throttle till it beeps and changes to -2-

then do a u-turn, repeat until you get to -1- and then finally it will change to normal operation mode

Link to comment
https://www.sau.com.au/forums/topic/130556-is-this-safe/#findComment-2415963
Share on other sites
SXR Rising Star

SXR

Posted
Posted
Hey this may sound like a dumb question and NO I haven't tried it yet but....

Installed a HKS evc the other week and need to calibrate it.

Don't have anywhere I can boot the car to do this, and don't wanna do it on the street ....so was wonderring if it is safe for me to jack the car up, put it on stands and drive it. (Like an excersise bike:) )

Or do I risk the car jumping off the stands or something worse?

It actually sounds quite stupid to me but was wonderring if its possible?

Thanks!

No it won't work you need the load.

Dyno would be the safest way

Link to comment
https://www.sau.com.au/forums/topic/130556-is-this-safe/#findComment-2415975
Share on other sites
dan_the_man Grand Master

dan_the_man

Posted
Posted

yeah just put the nose up against the garage wall and go hard with the gas pedal. let the car change gears as it needs to. you should prolly have your sister stand to the side of the car with a big palm leaf to blow cool air into the radiator... better to be safe than sorry right?

Link to comment
https://www.sau.com.au/forums/topic/130556-is-this-safe/#findComment-2421128
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Latest Posts

    • MBS206
      Slight brake pedal stutter after new pads

      By MBS206 · Posted

      Jack the back of the car up, pull that wheel off, pull that sensor out, and put a bore scope into the hole to inspect the outer casing, see if anything looks damaged before you pull the whole thing apart.
    • PranK
      Slight brake pedal stutter after new pads

      By PranK · Posted

      Ergh... So I pulled the speed sensor out again and the tip was shiny so I think it's rubbing the bearing. The bearing contains the magnets for the speed sensor so I think when the first sensor broke it damaged the magnet ring on the bearing.  This is just a Google image, but there is a hole going to the bearing. So when the tip broke off the old sensor I'm guessing it fouled the bearing... As the magnet is only protected by a plastic cover it would be easy to damage it. So I guess I'm doing a bearing again.   
    • GTSBoy
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By GTSBoy · Posted

      My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
×
×
  • Create New...