Jump to content
SAU Community

Recommended Posts

  • Replies 117
  • Created
  • Last Reply

Top Posters In This Topic

Hmmm, my studies have shown rumours of between 20000 kays and 18000 miles... From memory, the nismo page states 20, so that'd be the best bet.

Also, to anyone who said that i must have been mistaken, I most certainly was not. Turns out, the car was brought by a private buyer and has been sold before delivery to him to an unknown buyer for considerably less than the suggested prices. 6000 kays, absolutely immaculate. Also, there were only 20 made.

unfortunately you most definately were mistaken. there is no GTR Z-tune on the road in brisbane.

nismo site states the cars had to have less than 30,000kms.

funky, not like you to be off the mark. It's 20 total built not 100. it was conceived to commemerate nismo's 20th anniversary.
I always qualify shit I'm not sure by "I think"...

I think you suck teh wang.

:P I dunno why, I was never a big fan of the Z Tunes, so a somewhat lack of attention to detail.

I'm surprised Nismo didn't prebuy the GTRs before releasing the model. Coz if I lived in japan and owned a car that Nismo WANTED... I'd be asking a small fortune for it. f**k em... I want a piece of the pie too.

I bought 10 of them. f**kin piece of shit. i park them near shopping trolley areas and watch trolleys hit them

You need to turn the magnet off, its done by removing the engine and hitting a perfect combination of the 47 switches at the back of the bay.

Then hit the big yellow switch to engage chick magnet.

a blue one... hahaha

Yeh it was, a blue 34 Z tune... :|

Seriously, it was a Z tune or a damn good copy, I'm not stupid, lol

As you obviously know, the Z-tune only came in one colour - Nismo Silver.

I was just checking as we fitted the Z-tune front guards to a blue R34 GTR from Brisbane. It also has the

R-tune bonnet so it would be easy to see how somebody might mistake it for a Z-Tune if they were not familiar with it's design.

As the sole distributor for the Z-Tune in Australia, to the best of my knowledge there is no Z-Tune in Queensland. Nismo have no knowledge of this & they have a register of all owners. This register is kept to monitor the purchase of spare parts for the Z-tune as many parts are specific to the Z-tune and are not available to the general public. Owners must be on this register in order to purchase spare parts.

I would love to think there is one driving around up there but the information I have at hand tells me this is not so.

Cheers

Jo

so if I bought a Mines GTR and changed the wheels and bonnet because I didn't like it, you'd say thats not real?

easy to change the lights, maybe the owner didn't like the the little dotted type thingy lights.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
×
×
  • Create New...