Jump to content
SAU Community

Recommended Posts

http://www.mkiv.com/techarticles/filters_t...st/1/index.html

Regarding air filters. There's always going to be differences of opinion on who make good/bad filters. Nevertheless, I think most people would agree that K&N and Apex make very good filters.

it all depends on what you want - more power/greater air flow comes at a price - poor filtration. If you read the article you'll see that there is a big difference in how well the various filters actually filter...:(

OK, for a lot of people, a filter with really poor filtration (mainly foam filters) that is likely to lead to premature engine wear, don't care since they probably wont own the car for that long.

Me personally - my car had a Trust Airinx foam induction kit. It sounded great and probably gave me a little more power. but, holding the foam element up to the light and you could clearly see through it - the holes were measurable:( so you can imagine how much crap that it must be letting into the engine...

i've since replaced the Airinx with the factory original airbox. OK, maybe it doesn't sound as good, but as to the power loss - well, with the induction system my engine was breathing in loads of under-bonnet warm air, so that's debatable...

Cheers

Dave

Link to comment
https://www.sau.com.au/forums/topic/13227-best-air-filter/#findComment-252636
Share on other sites

Here's my experience with airfilters....

I bought a Rush O2 pod, which can flow more that almost all (or I think it is all) of the jap filters. The only difference I noticed was top end, it was less restrictive than the standard ryco paper filter....

I then put the factory airbox back in, and slapped in a K&N panel filter, and I have noticed no difference between it and the pod. You dont need a pod, a K&N panel is just fine. I dont personally have numbers to back me up, but if I cant feel ANY diffence, then whats the point...

Link to comment
https://www.sau.com.au/forums/topic/13227-best-air-filter/#findComment-255050
Share on other sites

Biggest difference I have ever noticed was replacing the standard paper filter with a K&N paper filter, again though, its only high end, and marginal at best.

From what I understand, adding a second cold air intake (say from the front bar) has more effect, but requires drilling a large hole in the line, so I havent done it yet.

check this out for more info

http://www.autospeed.com/cms/article.html?&A=0009

Link to comment
https://www.sau.com.au/forums/topic/13227-best-air-filter/#findComment-255306
Share on other sites

  • 2 weeks later...

the only mods ive done is POD filter, Cold air induction, Cat back exhaust to lukey muffler. im unsure if the clutch is aftermarket but ive done so many drops and its only ever slipped once, its bloody strong. i was averageing 8.2-8.5 and then i did one nice run of 7.26, last time i tried i got 7.69 but im taking it easy now :)

Btw was heavily loaded with SUb and spare in the back im looking forward to faster times hehe

Link to comment
https://www.sau.com.au/forums/topic/13227-best-air-filter/#findComment-296936
Share on other sites

My mecahnic told me POD filters are perfectly legal, i hope they are lol, i just sold my K&N panel filter on ebay, it only did a few kilometers on it, but i realised the airbox had a ceratin vacuum spot, cos one part of the filter was so dirty and the other was so clean. My POD sits in the front bar gettin totally fresh air.

Link to comment
https://www.sau.com.au/forums/topic/13227-best-air-filter/#findComment-306942
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
    • I would say no, why, because my daughter, who also lives in Goulburn, hasn't recommended us going there Pity, as we miss all the German joints around in Sydney, actually, the restaurants are the only thing I really miss about Sydney, and a special mention to Ishibanboshi at Bondi Junction, their Kara-age Don is heart cloggingly deliciousness (always added a special boiled egg...or 2) 😋 
    • Does that German restaurant still exist in the old place out the NW end of Goulburn? When I say "out the NW end of"...I am really being vague. It was 1997 when I was last there, and the only point of reference I can recall is that it was on the opposite side of the main drag from the big merino. And when I say "opposite side of the main drag", I don't mean "on the main drag". It was either a couple of streets back from there, or might have even been out in the sticks a bit further. Was an old farm building or mill or somesuch. And when I say "the big merino" I might actually be thinking of a completely different part of town, because I just looked on maps and the big bugger is not where I remembered him to be! The food was good, consisting largely of various German mystery-meat sausage/loaf things and kartofflen.
    • So while the second sentence is completely correct and the whole point of the conversation, the first sentence bears consideration. If this bloke is just hoping to throw big turbos on and drive it around, because there are no helpful facilities at all in his tropical paradise** then he likely has zero chance of even knowing what the TP is on the last column in the stock maps, let alone know whether the ECU is operating anywhere near it or past it. So the point is very very moot. And, per what I said before, at stock boost on those turbos, you may well be off the end of the map. **I'm just back from Vanuatu, so I know exactly what small Pacific nations can be like wrt paradise without requisite facilities. But it's not even that simple. I put a high flow on my car and had to drive it around without a proper tune because of the lack of opportunity*** to put the bigger AFM and injectors into it to allow it to be tuned. I had to turn the boost down to less than I had before, and back off the boost controller's ramp, because it was exploring parts of the map that it didn't drive in before, and really couldn't access for tuning on the dyno either, and so was pinging. It was still well within the last column, because when I first**** set up the Nistune on the Neo I rescaled all axes of the maps to give some more space to explore. ***Family dyno was broken ****This was 13 years ago, and the TIM thing wasn't a thing then and so TP would definitely grow when pushing past the stock tune's limits.
    • Yep, this bit another local owner. I caught it before putting the transmission back into the car, what I noticed was the pressure plate fingers weren't flat and even. It's more obvious with the pull style clutch because the throwout bearing ring was visibly not flat once everything is put together. Nismo should really update their instructions to call out this specific detail. I'm not even sure the clutch as-shipped orients everything properly.
×
×
  • Create New...