Jump to content
SAU Community

Recommended Posts

Question: Is redlining your car a good or bad way to drive it? Let me give the example by redlining I mean shifting at 7000 rpms. I have a 95 r33 gts-t and when i drive it the shifts between 1st and 2nd usually come at 5000 rpms, 2nd and 3rd 5000 rpms, 3rd and 4th 7000 rpms and 4th and 5th 7000rpms. I wanted to kno if this will affect my engine in a negative way. This is not everyday driving just when im in speed mode and want to remind my ride tht she still is a sports car. What do u think good or bad? All answers welcome.

Link to comment
https://www.sau.com.au/forums/topic/132577-for-the-experts/
Share on other sites

well..as long as u dont do it often it should be ok....

and by the sounds of things, you should be doing about 180 on 4th - 5th - so perhaps take it to the track.....

You are absolutely correct by 4th doing about 5 or 6000rpm the speedometer is maxed out so by 5th it doesnt eve make sense lookin at the speedometer. So does tht mean the cars top speed cannot be measuredby the stock speedometer if so wht is the max speed for a 95 gts-t completely stock.

Link to comment
https://www.sau.com.au/forums/topic/132577-for-the-experts/#findComment-2457766
Share on other sites

Redlining at 7000 RPM = thrashing.

If you thrash your car, dont expect it to last as long.

I drive an auto, when driving normally I let go off the gas at around 2000 RPM... then go back up to 2000 RPM.

Also I never go over 2000 RPM when the car is warming up for the first 10 or so minutes...

Link to comment
https://www.sau.com.au/forums/topic/132577-for-the-experts/#findComment-2457779
Share on other sites

You are absolutely correct by 4th doing about 5 or 6000rpm the speedometer is maxed out so by 5th it doesnt eve make sense lookin at the speedometer. So does tht mean the cars top speed cannot be measuredby the stock speedometer if so wht is the max speed for a 95 gts-t completely stock.
I personally think you're a dipshit, with no regards to other peoples safety :). If you want to do such speeds take it to the track, or any other legal motorsport.

Mods please close and remove this topic :laugh:

Link to comment
https://www.sau.com.au/forums/topic/132577-for-the-experts/#findComment-2458533
Share on other sites

This is not everyday driving just when im in speed mode and want to remind my ride tht she still is a sports car.
I personally think you're a dipshit, with no regards to other peoples safety :). If you want to do such speeds take it to the track, or any other legal motorsport.

Mods please close and remove this topic :laugh:

Agreed..

We are going to see more and more of these incidents/posts as the R33's are becoming dirt cheap now. Affordable for young P platers and the like.

Link to comment
https://www.sau.com.au/forums/topic/132577-for-the-experts/#findComment-2458613
Share on other sites

its a sports car, and hence it can withstand some redlining - but not all the time. And as the others have said (and as I mentioned), if your ever in the mood to go sick with the speeds - tracks are the best option man. I admit, I am very tempted to take the car to its limits - but not on the roads. I live in Mt waverley (vic) and the traffic here is quite intense - very easy for someone to have a crash get hurt or even die...

So - after all that, if u feel the need for speed - track or drag strip.....

Link to comment
https://www.sau.com.au/forums/topic/132577-for-the-experts/#findComment-2458632
Share on other sites

Hmmm redline? Meaning possible failure and crash increase, hmmm i think someone will come unstuck oneday, and should keep there redlining to the tracks and off the road.

But O/T you should treat your car better than that, just becoz you can do it now and then, doesnt mean sh!t, Your just putting other people including yourself at risk, so aggreed this topic is sorta pointless and should be closed as sending the wrong message to others out there i think?

Link to comment
https://www.sau.com.au/forums/topic/132577-for-the-experts/#findComment-2458757
Share on other sites

i agree with most of you on here that high speeds should be kept to the track.

as paulr33 said redlining is pointless in a stock r33 as peak power is 6400rpm or so from memory

having said that high speeds should be kept to the track if that situation was right on an open road with no trafic where speed limit is 100 i would probly take it to 160 if it seemed fairly safe, any thing over 160 is rediculus on public roads.

Link to comment
https://www.sau.com.au/forums/topic/132577-for-the-experts/#findComment-2472024
Share on other sites

Agreed..

We are going to see more and more of these incidents/posts as the R33's are becoming dirt cheap now. Affordable for young P platers and the like.

It is for the tracks maybe you should ask b4 assuming. And to Al F%$K off you dont kno me asshole.

Link to comment
https://www.sau.com.au/forums/topic/132577-for-the-experts/#findComment-2475211
Share on other sites

....................... 3rd and 4th 7000 rpms and 4th and 5th 7000rpms. I wanted to kno if this will affect my engine in a negative way. This is not everyday driving just when im in speed mode and want to remind my ride tht she still is a sports car.
Please explain this, or are you now changing your story :O. That phrase implies that you are doing this on the street. I may not know you but i have only replied to what you wrote, thus you are a FOOL!
Link to comment
https://www.sau.com.au/forums/topic/132577-for-the-experts/#findComment-2475660
Share on other sites

  • 2 weeks later...
Redlining at 7000 RPM = thrashing.

If you thrash your car, dont expect it to last as long.

I drive an auto, when driving normally I let go off the gas at around 2000 RPM... then go back up to 2000 RPM.

Also I never go over 2000 RPM when the car is warming up for the first 10 or so minutes...

babied hard.

Usually until its warmed up I just make sure the car stays off boost. I usually like to rev it up to about 3gran (off boost). Keeping it below 2000RPM usually puts the motor under more load which i assume is bad for a cold engine

Link to comment
https://www.sau.com.au/forums/topic/132577-for-the-experts/#findComment-2503983
Share on other sites

babied hard.

Usually until its warmed up I just make sure the car stays off boost. I usually like to rev it up to about 3gran (off boost). Keeping it below 2000RPM usually puts the motor under more load which i assume is bad for a cold engine

Its not bad for the motor unless your in top gear trying to lug it out of a corner with the motor clearly labouring.

Select the correct gear for the road speed and it will be perfectly fine.

Link to comment
https://www.sau.com.au/forums/topic/132577-for-the-experts/#findComment-2504110
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
×
×
  • Create New...