Jump to content
SAU Community

Recommended Posts

hey all

thinkin of buyin a 33 GTR in a few months time.

just been doin sum research on them and have read about the differences between the two with the ATTESA system:

ATTESA E-TS (Skyline GT-R)

The Skyline GT-R adopts the ATTESA E-TS Electronic Torque Split 4WD System that optimally controls the torque distribution to the front and rear wheels according to the driving conditions. Based on a rear-wheel-drive configuration this advanced system can vary the front-to-rear torque split in a range of 0:100 to 50:50.

ATTESA E-TS PRO (Skyline GT-R V spec)

The GT-R V spec model features the ATTESA E-TS PRO System that provides integrated control of the driving and braking forces at all four wheels independently, enabling each wheel to deliver its full performance potential. This system consists of ATTESA E-TS for optimum front-to-rear torque split control, Active LSD for optimum control of the torque split to the right and left rear wheels and ABS. These capabilities combine to deliver optimum traction steering response, stability and braking performance on all types of road surfaces.

What i want to know is on the track is the Vspec GTR much better (handelling) than the normal GTR???

thanks

luke

Link to comment
https://www.sau.com.au/forums/topic/133116-33-gtr-vs-33-gtr-v-spec/
Share on other sites

Actually you are right, I couldn't.

[bows to the audience]

Biggest difference is some Racepace tweaking and an SK suspension system. Plus being purple it's naturally faster :D

Noticing not very many contributing here. What? All afraid to destroy the legend of V-spec? It's really just marketing BS much like HICAS. There may be some minimal difference on stock brand new cars but after some upgrades that's all out the window.

I agree with Geoff, Attesa E-TS has a reaction time of 1/100th of a sec, Attesa E-TS Pro has a reaction time of 1/1000th of a sec...but as i said in the other post about this topic....It's all about the sticker baby! :( even though some people have it on their normal GTR's :(

Seriously though don't base your purchasing of a car on a V-Spec or not, if you find a suitable one and it's a V-Spec think of it as a bonus....it isn't much more.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...