Jump to content
SAU Community

Recommended Posts

hey dudes.

im stuck with what turbo to chose on my car.

its an r32 gtst with the following mods:

FMIC

turbotech boost controller

bosch 040 fuel pump

K & N pod

Dr.Drift Remap running 14psi.

my aim is around the 190-200rwkw mark. i currently have 169rwkw with the above-mentioned mods.

im stuck in chosing these turbos:

Straight RB20 Turbo Highflow

Highflowed/Bored Turbine housing to fit larger steel/inconel Turbine wheel and shaft.

Highflowed/Bored Compressor Cover to fit larger alloy Compressor wheel.

This makes the Turbo Hi-Flowed both Compressor side and Turbine side.

The upgrade bolts directly back on the manifold and existing exhaust.

The housings are acid dipped and sandblasted back to new quality.

This is a journal bearing highflow and is capable of making 210-220rwkw and is rated to 18 psi max boost.

1 bar of boost is available from as little as 3000rpm.

Straight RB25 Turbo Highflow

Highflowed/Bored Turbine housing to fit larger steel/inconel Turbine wheel and shaft.

Highflowed/Bored Compressor Cover to fit larger alloy Compressor wheel.

This makes the Turbo Hi-Flowed both Compressor side and Turbine side.

The upgrade bolts directly back on the manifold and existing exhaust.

The housings are acid dipped and sandblasted back to new quality.

This is a journal bearing highflow and is capable of making 220-230rwkw and is rated to 19 psi max boost.

1 bar of boost is available from as little as 3400rpm

i wouldnt mind boost hitting me at 3000rpm, but then again, the rb25 unit would have more mid-range and top end, correct? for driveabilty and whatnot, what would be better suiterd to my needs, and mods?

any comments (good or bad) are welcomed.

thanks guys

jabba

Link to comment
https://www.sau.com.au/forums/topic/133351-turbo-choice/
Share on other sites

There is no difference between rb20 and rb25 hiflow. They get hiflowed to the same specifications. You can make boost come on earier, it all depends on intake setup, exhaust setup and state of the tune.

Link to comment
https://www.sau.com.au/forums/topic/133351-turbo-choice/#findComment-2471512
Share on other sites

There is no difference between rb20 and rb25 hiflow. They get hiflowed to the same specifications. You can make boost come on earier, it all depends on intake setup, exhaust setup and state of the tune.

There is actually a difference.

The compressor cover limits the size of the wheel that can be used in the R32 turbo.

The RB25 turbo and VG30 turbo have larger compressor covers thus larger wheels can be used that flow more air creating more power.

The R32 and R33 turbine housings are also different in size but do not affect power as much as the compressor cover size difference does as for an example a stage 1 and 2 wheel can be used in all 3 turbine housings- R32, R33, VG30 :O

Link to comment
https://www.sau.com.au/forums/topic/133351-turbo-choice/#findComment-2471893
Share on other sites

Paul is talking about the GCG highflow and is correct the internals are bored out to roughly the same size and rated at the same HP.

But everyone does there highflows different hence slides answer

where are you getting the highflow done?

cheers

Edited by Munna1
Link to comment
https://www.sau.com.au/forums/topic/133351-turbo-choice/#findComment-2472831
Share on other sites

you want to hit boost at 3 grand but are fitting a larger turbo?

those two don't match up and you'll likely add more lag.

specially choosing a gt3040r, don't expect much before 4500 ish

I had one on my r33 with the smaller exhaust housing to bolt on to standard manifold making full boost by 4000 to 4500 on 18 psi

Link to comment
https://www.sau.com.au/forums/topic/133351-turbo-choice/#findComment-2472889
Share on other sites

im leaning towards the rb20 hi-flow unit.

but will it run out of puff? spose it doesnt matter, coz im not gonna drag it in the near future.

sure the rb25 unit is more laggier, but it will obviously last longer.

i just want something with some get up and go,

i dont really want more than 200rwkw atm either.

so probably the rb20 unit.

Link to comment
https://www.sau.com.au/forums/topic/133351-turbo-choice/#findComment-2472906
Share on other sites

Yes I agree with Slide . I think he is telling you that the RB25 and VG30 versions use a larger diameter compressor wheel with a matching larger compressor cover . These would accept 70-71mm compressor wheels more easily than the covers on the smaller RB20 type compressors . This makes the RB25's turbo (housings really) a bit more flexible with compressor options . So in other words unless you want to stick with 60mm diametre compressor wheels ie dinosaur T3 wheels or a GT28BB cartridge the RB25 is the go .

Link to comment
https://www.sau.com.au/forums/topic/133351-turbo-choice/#findComment-2473552
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...