Jump to content
SAU Community

Recommended Posts

I had a problem with the rear passenger door glass hitting the hard rubber surround along the top edge whenever I shut the door with the window up.

This would always cause an air leak sound even at low speeds. So I had to lower then raise the window everytime the door was opened.

Stagea, in their infinite wisdom, put in adjustment screws to help with this problem and the following was my attempt to fix the glass level.

post-25601-1158241205.jpg

Screwdriver shows where to prize off the door handle plastic surround - On the top front edge.

post-25601-1158241333.jpg

Picture of the back of the plastic surround shows the single clip.

post-25601-1158241549.jpg

Underneath is the mounting screw for the panel. 10mm socket works easier than the phillips screwdriver. The rest of the panel comes off by simply pulling around the edges to release the clips. A short, sharp yank with your finger tips is all that is required. See pictue below for where the mounting holes are situated.

post-25601-1158241720.jpg

Be sure to disconnect the electrics - a small screwdriver is needed to release clip, then slide out.

post-25601-1158241862.jpg

All off and admiring the view. Plastic weather protection will need to be removed along the top edge to get at the level adjustors. Pull gently on the plastic without stretching it out of shape and it will stick back into place.

If you look carefully, you'll be able to see the holes where the plastic mounting clips go - so you'll know where to pull on the door trim. Check out the quality of those speakers - the factory must have spent a whole $5 on those babies! And $1 on the foam.

post-25601-1158242015.jpgpost-25601-1158242348.jpg

This picture shows the level adjustors with increments. You can see by the worn ring mark in the paint where it used to be and how far I had to drop the glass. There are two adjustors - one for the front edge and one for the rear. I only needed to adjust the rear to fix my problem.

post-25601-1158242097.jpg

This picture shows the little cloth pads that the glass runs against when moving up and down.

They can also be adjusted to change the angle of the glass on the 'in and out' plane - if that makes any sense. I believe they need to be left with a reasonable amount of play in them as the window changes angle as if feeds up and down. Keep these clean or you will scratch the glass.

The best position to have the glass is where it will just pop under the edge of the hard plastic surround on the body without getting caught on it.

I hope this help you enjoy noiseless motoring and to avoid breaking something unnecessarily.

Happy tinkering,

Warren

Edited by 3intheBack
Link to comment
https://www.sau.com.au/forums/topic/134380-rear-door-window/
Share on other sites

Beatuful, GREAT writeup! This might get lost in the Stagea section, so you might want to think about having it moved to the DIY section, either way, I am putting a link to it in the "Mega Stagea Link" thread :)

Again very nice writeup! Thanks!

  • 1 year later...

i did it the other day but i cant remove the damn plugs to the power controls. How did you unplug it? the side morrow adjuster can be unplugeed easy but not the power window one. Lemme know. thanks

Yudy

  • 1 month later...

All the electrical plugs use the same locking system. You need to push in the little clip on the side. Use a screwdriver are similar. It can be a prick of a job as you need two hands to unplug it and two hands to hold the door fab.

  • 1 year later...
i did it the other day but i cant remove the damn plugs to the power controls. How did you unplug it? the side morrow adjuster can be unplugeed easy but not the power window one. Lemme know. thanks

Yudy

Having this same problem, driver's side front on S2... power controls plug (the big one) doesn't matter how far the locking tab is depressed, it's stuck like glue. Yet I know it's not glued 'cause I plugged it in myself not 4 months ago.

  • 3 years later...

We had been having trouble with window alignment of the left rear door window glass in our S2 for a while.

Recently i had the door to a point where i could make some minor adjustments and then i found the alingment problem for our car.

I found that there is a small white plastic bush that slides in the glass runner, which the regulator arms are mounted to via a little metal balljoint. I found that plastic bush was split in half and allowing the glass to lay back.

I have been into Nissan and i was told that i can't even buy a new complete regulator.

Has anybody found this same problem and be willing to share a solution.

Cheers, Jason.

  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
×
×
  • Create New...