Jump to content
SAU Community

Recommended Posts

my search came up with lots of topics on how to remove, but not if its bad for engine/turbo etc.

my R34 GTT is on 10psi with stock turbo, just recently under heavy acceleration it seems to missfire asif traction control is on (which it isnt) and i get lovely pop pop pop pop noise (while accelerating) towards redline, happens occasionally not consistantly..

could this be the R&R i've heard so much about? but why havent I had this issue before today?....

rich and retard isn't a popping sound. it is just a dead stop in power. it sounds like you have ignition issues, like a dud coil or spark plug. this isn't that bad as it isn't really doing anything except not sparking. it would actually be cooling the cylinder that isn't firing.

i put boost to 11psi, doesnt happen anymore..

no farken idea.

it almost sounds like a rev limiter so it might pop every .3 seconds under the hard acceleration, then just stops.

power seems to die for the .3 seconds, or whatever, boost holds.

either way, problem gone for the moment.

Hmm, I'd go to the dyno and get your fuel ratios checked.

Popping is most commonly because its too rich. Rich mixture is harder to ignite. Then the mixture is burnt after it has exited the cylinder giving a pop. Usually caused by the air flow metre detecting too much airflow, (usually from intake mods like fmic and pod). The EUC adds not just a littlle more fuel, but a lot more. Too much infact as it thinks the excess flow is a problem.

I regard to the issue going away after the boot rise...

I can't say for r34's, but with 33gtst's, it would seem that the fuel pump only supplies enough fuel for std boost.

Your poping might have gone on higher boost because your fuel pressure might be dropping, and themixture is coming back to lean, or at least closer to where it should be.

Anyway, there are 101 answers to this.

IMO minor popping, as long as it is a minor misfire is not going to cause imidiate problems. However, if it is running rich, and you don't do something about it, then you risk other issues like cat damage and washing the bores.

Best best, get it checked on the dyno and then talk to the tuner about a course of action. Most probably ECU, maybe a fuel pump.

Chriso

Wow, I was JUST about to add about richness damaging the cat. Good point!

I have experienced an engine running way to rich and damaging the cat in a 3SGTE, which has the cat IN the DUMP PIPE! Stupid place I know, so more prone to getting damaged I guess... but yeah, amazing how much power you will be loosing if you are both running rich AND have a blocked cat.

I went from 62fwkws to 125 fwkws on that car with hi flow cat + retune.

Edited by psybic
then you risk other issues like cat damage and washing the bores.

cat damage i undertstand, but 'washing' the bores? i didnt know this was possible. my understanding is that running rich only cause rediculous fuel consumption (blocked o2 sensor) and damaged/blocked cat.

unburn fuel will damage the cat if it gets to much..

other wise miss shouldnt have any detrimental affects..

it will also use more fuel

is damaging the cat really that bad a thing? wont it just start to become a "high-flow" cat?

i put boost to 11psi, doesnt happen anymore..

no farken idea.

it almost sounds like a rev limiter so it might pop every .3 seconds under the hard acceleration, then just stops.

power seems to die for the .3 seconds, or whatever, boost holds.

either way, problem gone for the moment.

Id say its a spark problem, weak coils possibly not causing a powerful enough spark. The higher boost level is blowing the spark out. Try gapping your plugs down (requires less energy for the spark) Also 11psi is as high as you want to boost the stock turbo. It wont last much longer above this level.

Its a very common problem, usually coil/sparkplug related. However it could be something else.

Read all about it here http://www.skylinesaustralia.com/forums/in...showtopic=32356

Edited by Rolls
ahh, no...

it melts and causes a major restriction or blockage in the exhaust system, not what you want.

i guess ur assuming that when it melts u turn the car off and let it set... my guess is that the melted bits will be blown out the arse of the car.

what happens in reality, is the cat will usually break apart into pieces that are too large to go out the exhaust, but they block the outlet in the cat, (exhaust pressure pushes the loose bits to the outlet of the cat causing restriction) and your car doesn't make much boost/power due to the restriction and it can't melt further because the exhaust temps dont get high enough, because the vehicle isn't making any power.

the above has happened on almost all vehicles i have changed cats on, and they aren't all performance vehicles either.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If you mean the alarm immobiliser; theyre internal to the alarm itself which makes that difficult; I couldnt even see where he put it; its not in the same place as last time; but with all black wiring it might be very challenging to trace  I had someone turn the key for me as I know it only primes for a couple of seconds As my post above; I am getting no voltage to the pump at all; but I am testing continuity of the power line (SB) from the pump plug to the relay fine. As well as the negative from the pump plug to a 12V constant.    Yeah; he blammed the no start on a bad battery; said I needed to get a new battery and it'll start. Turns out the battery drained because the tail lights had been on for half the day during the install (the rubber cushion on the brake switch gave out while he was testing it as I have a picture of the car from that morning with the tail lights off..i've replaced that). The battery was turning over the engine just fine for a long time; but got low since lights were draining it so it was too low to test a start after he finished. I bought a new one on his advice...$250 wasted. My original battery charged up just fine and is healthy.    It was running perfectly fine when I messed up the old alarm (programmed out the remotes). He couldnt start it after removing the old alarm; my assumption is that when he unhooked it; he didnt bridge the circuit back when trying to start it. Its always been perfectly fine. The ECU swap and pump were 2 years ago. It's never missed a beat in that time. 
    • This is a big issue for me without the diff. I just have zero drive from the passenger side when drivers side has no traction. Bec's parents place has a crazy steep driveway with odd camber and I have never been able to get up. My bro-in-law's 130i with an (unknown brand) LSD gets up fine as does their dad's Hiace. My car stays at the bottom. We have other odd camber roads around here as we're elevated a bit and if it's raining I can get totally stuck around some hairpins. 
    • Yeah, I am super excited for this.
    • Was the car running before he touched the car?
×
×
  • Create New...