Jump to content
SAU Community

Recommended Posts

After a decent set of front pads for my car for street / occasional track use.

Last set were bendix ultimates and i wasn't really happy with them as they put out heaps of dust and didn't really have much bite. Some have said ferodo or endless pads are ok? Where can i get them and how much have you paid?

Link to comment
https://www.sau.com.au/forums/topic/136366-brakepads/
Share on other sites

yeah, they're an alright pad.... you can use them on the street (i run them) but they're better suited to the track/spirited driving (i.e. mountain runs etc) as they take a while to get some heat into them.

I used to run Racebrakes RB74's on the front / bendix ultimate on the rear previously - not a bad combo.

now i run DS2500's front and the same bendix ultimates on the rear... lol... they don't seem to wear out :|

just don't make the same mistake that i did and get the same pads front and rear... doesn't work :S

Link to comment
https://www.sau.com.au/forums/topic/136366-brakepads/#findComment-2535515
Share on other sites

I've actually got lucas pads in, Im suprised at how good they go. Bit of dust but not too bad. WAY better than the rb74s dust wise, and they arent eating my disks as much.

Dont know about track tho, but havent had fade on the street, and sometimes I give them a bit of a go just to make sure everything is still working.

Dont know exactly the type tho, they would have been about $100-110 a pair.

Link to comment
https://www.sau.com.au/forums/topic/136366-brakepads/#findComment-2537880
Share on other sites

Green EBC racing pads

I found these to be quite expensive for the performance they provided...

I will not use these again personally as they dont offer very good value for money...

bendix ultimates,

Had these on at the last track day and after 5 laps i had no brakes left...

Try Ferodo DS2500 for street/track.

I have just ordered a set of DBA slotted rotors for all four corners and i have purchased a set of these to go with the slotted rotors...

The bloke who set up our brakes for targa tas swears by them for street/track use and id have to say they were impressive in our targa car...

Link to comment
https://www.sau.com.au/forums/topic/136366-brakepads/#findComment-2538415
Share on other sites

Yeah, I won't touch EBC Green stuff again. Apparently I got a bad batch but the ones they returned to me were exactly the same and disintegrated within a month after screaming their tits off at the lightest touch of the pedal!!

I am running Ultimates at the moment and they are very dusty and I don't think they are anything special. Might have to invest in a set of Ferodo's before track day!!

Link to comment
https://www.sau.com.au/forums/topic/136366-brakepads/#findComment-2538576
Share on other sites

hmmm after seeing greenstuff used on a mates 180sx i recommended them to a mate with a sss pulsar.... great on the 180, havent got feedback from the sss... I know theyve been on the 180 for ages, with a set of bda slotted's. do an awesome job, we fitted them ourselves with a VERY noticable difference with minimal brake-fade after a lap or few of lakeside, so yeah. a "bad batch" really shows the quality and consistancy of a brand though, i guess. if someone relies on a brand then all of a sudden they get a "bad batch" and they are f***ed.... not cool. but to my own experience, fantastic... havent PERSONALLY come across an issue.

Link to comment
https://www.sau.com.au/forums/topic/136366-brakepads/#findComment-2538589
Share on other sites

I used DBA 4000 rotors front & rear, Ferodo DS2500 front and RB74 rear with MOTUL 600deg fluid on the 33 and they could lock the tyres easy as. Only problem was the were VERY squeeky on the street when they were cold & the dust from the ferodo's had me washin the wheels after every spirited drive. otherwise great set-up

Link to comment
https://www.sau.com.au/forums/topic/136366-brakepads/#findComment-2542550
Share on other sites

I used DBA 4000 rotors front & rear, Ferodo DS2500 front and RB74 rear with MOTUL 600deg fluid on the 33 and they could lock the tyres easy as. Only problem was the were VERY squeeky on the street when they were cold & the dust from the ferodo's had me washin the wheels after every spirited drive. otherwise great set-up

No offence Shane (as much as its not a bad set up) locking the wheels means one of 2 things. You hit the brakes too hard, or you have crap tyres (or both so I guess that is 3...)

Link to comment
https://www.sau.com.au/forums/topic/136366-brakepads/#findComment-2542619
Share on other sites

I have used Endless EuroX (the closest thing these days would be CC-X) and they were great but needed to get heat into them to work really well. Stood up to 5 laps of QR brilliantly.

Bendix Heavy Dutys were crap, and dusty.

A friend who does lots of hillclimbs and has held the record at Mt Cotton reckons the Ferodo 2500s are good.

I'm using QFM pads at the moment. For the price (1/3 of the Endless prices I was looking at) they're good.

http://www.skylinesaustralia.com/forums/in...howtopic=136212

Got them through John at GMR Fairfield (3844 2855).

Link to comment
https://www.sau.com.au/forums/topic/136366-brakepads/#findComment-2558289
Share on other sites

I'm getting Hawk HP Plus next, I went in a car with these and it hurt my face everytime the brake pedal was planted :D

Hahaha, But you must admit it was a definite improment to your facial features.

On a serious note, Hawk HP Plus are an excellent brake pad for high performance street cars that also make it to the track.( Not that my car would be classed as high performance by any stretch of the imagination) Hawks have a high temperature coefficient and zero brake fade after 2 sets of the National circuit at QR (in succession). They work extremely well from cold, and give fantastic feedback through the pedal. I use them with Motul RBF 600 FACTORY LINE fluid.

The only downside would have to be the very slight squeal you can develop if you don't use the brakes hard enough for a long period of time, say over 2-3 weeks. But all it takes to bring back the sound of silence is to do a couple of 100km to 30km heavy brakes and things are back to normal, or attend a track day. This just help keep the rotors clean and free from any dust.

The brake wear is not too bad. The hawks I recently replaced lasted 2 and a half track days, and about 10K km of driving in between, but being an auto I think they get abused alot more than a manual. A friend had hawks on his 33GTR Vspec2 and they lasted most of the year and he attended most of the track days.

Anyway, a big :P from me.

Link to comment
https://www.sau.com.au/forums/topic/136366-brakepads/#findComment-2559256
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...