Jump to content
SAU Community

Recommended Posts

Dropped my car in to Belconnen Discount Tyre Service this morning, and amongst other things whilst chatting with Mark (top bloke, really knows his shit) i saw my new 255/35/R18 Dunlop SP Sport MAXX's off the rims.

WTF

They are f**king huge. I mean, i used to look behind Boxsters and 911's and go, wow they are big tyres - f**k no move over. By Huge i mean they are comparable to my Forearm (i'm 6 foot 3).

Also got him doing a wheel alignment and looking over the suspension to see whats there, if any of the bushes are shagged and grease it up.

Top bloke - knows what he's on about, owns a Stagea, and will look after you.

Edited by nsanity
Link to comment
https://www.sau.com.au/forums/topic/136373-i-knew-they-were-wide-but-wtf/
Share on other sites

tires arent cheap, 300ish for Federals the new type and they are quite good. Except now i am wheelspinning coming on boost in second might need some new ones.

$430 ea for Dunlop SP Sport MAXX's, 255/35/r18, to put things in perspective, the fronts (235/40/R18) will only be $315ea.

wider tyres = more drag on long journeys = increased fuel consumption.

you should have thinner tyres for everyday driving and just use the wide ones for track days. better yet get semi-slicks :rofl:

I'm actually in a bit of a pickle at the moment in regards to rims;

I want a new set of rims but I'm not keen on dropping down tyre width from 255 to 235s which most rims these days seem to take.

Is there really that much difference when it comes to tyre width?? Obviously the more tread I have the better grip I get and fuel consumption isn't really a concern of mine but is 20mm going to really impact me?

Depends on the quality of the tyre you're using I reckon.

The cost of an 'ordinary' 255 width tyre might be the same as a really good 235 width tyre. The 255/40ZR17 Nexen N3000's that came with my mags when I bought them are nothing short of utter shite at the retail cost of $190 each, which is cheap for any brand's "top of the line" tyre. As a (bad) comparison, the 225/50ZR16 Falken Ziex 512 tyres I had on my old 16's absolutely shat on these Nexens from a rather great height in every way.

Even the 205/50R16 Vredestein Sportrac 2's I had on the front 16's had much better handling than the 225 Nexens I have now.

I suppose what I'm trying to say is instead of spending money on a new set of wheels with some normal tyres, get some decent tyres for the mags you have and you might end up better off.

I'm fairly sure that the wider the tyre you using on the front will give you heavier steering, which you may or may not want. I quite liked the difference in steering feel my car had when I went from a 205 to a 225.

I'm actually in a bit of a pickle at the moment in regards to rims;

I want a new set of rims but I'm not keen on dropping down tyre width from 255 to 235s which most rims these days seem to take.

Is there really that much difference when it comes to tyre width?? Obviously the more tread I have the better grip I get and fuel consumption isn't really a concern of mine but is 20mm going to really impact me?

Honestly it depends on the tyre.

If you go from say nankings or hankook k104's or nexens, to say High end dunlop, yoko, goodyear stuff - irregardless of size, you will notice a world of difference, assuming you have it properly aligned.

The New Dunlop SP Sport Maxx's i have on my rears are unbelievable for traction even though they are barely scrubbed in. Even over the K104's i had before they started doing scrubbing problems.

I remember the red widebody R33 GTS-T that Parvis used to have in the F&F imports showroom(the old location)that had 335 section tyres... F**K me;huge!

That car was a beast... And we actually took the rear wheel off the car..

IT was SOOO BIG!!!!!! The front wheels were a 10 inch rim, and the rear was 12.5 i believe!!!!

for the price of a set of 255s you can get much better 235s, as bluprint is suggesting. this is particularly the case since commondoors take 235s and the economy of scale makes them cheaper. add far wider choice and it's a win both ways. add to that less tramlining and smoother ride; unless you're dragging, in which case wider might always be better, i'd rather go for good 235 than an average or unknown 255 anyday. just my 2c.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...