Jump to content
SAU Community

Recommended Posts

i have 2 x 15" 1000 watt rms subs with stupidly big magnets connected to them which i have to install, atm i only have one in in a fairly large box, which i needed to remove my spare tyre to get in, i havnt looked far into the boxes yet, just wandering if anyone knew if i could get a dual 15" box which would fit strait in or even 2x boxes, and keep in mind they cant be too shallow thx in advance

Link to comment
https://www.sau.com.au/forums/topic/137648-big-sub-setup-in-r32/
Share on other sites

so your saying i should make 2x 15" holes in my bootlid and mount them in? genious!!

now serious help please, i know its a bit ridiculous but i had 2x 12" alum 1000 watt rms subs and i duno... just didnt have the deep low rumble i like, i know it will fit all i wanted to know was if any body knew any boxes which would fit strait in, to try make life easier for me before i go to the effort to make one myself or get one custom made depending on how lazy im feeling

Edited by nemz
so your saying i should make 2x 15" holes in my bootlid and mount them in? genious!!

now serious help please, i know its a bit ridiculous but i had 2x 12" alum 1000 watt rms subs and i duno... just didnt have the deep low rumble i like, i know it will fit all i wanted to know was if any body knew any boxes which would fit strait in, to try make life easier for me before i go to the effort to make one myself or get one custom made depending on how lazy im feeling

short of removeing the rear seat that is the only realy way I can see 2 15" subs in there properly.

hahah yeh i have my new body kit on its way here now finally completed and my car is gone till jan 10th :) im spewing man, i cant beleive my car got impounded for a measly little chirpy into second gear.. and yeah all that gear did go in

list of it goes

1x 1 farad capacitor(soon to have an extra 4 farad for sub amp)

1x earthquake 900.5 amp for speakers

1x lanzar 4000 watt mxa 282 amp 2 channel sub amp(if you dont know who lanzar is, its made in the usa by boston acoustics)

2x audiopipe 1000 watt rms 15" dual 2.5 inch voice coil subs

the lanzar amp takes up the whole length of the back of the seat, and earthquake which is pictured as the blue amp in that pic takes up the rhs and the box is a shall box which takes up the whole height of my boot and almost width and lenght so yeh when you open all you can see is system and no floor, it was a bit messy but will re wire and stuff to make it look better when i get the car back

speakers

- earthquake 400 watt 5x7 in doors with tweeters

- earthquake 600 watt 6.5" splits in rear

deck

- pioneer deh-p5750mp

3x 5v pre out with full sub control + multiple amp control

mp3,wma etc

remote

wires

dual 4 guage wires with gold plated terminal

100 amp fuse

3x cadence rca's (i wouldnt recomend these im changing very soon)

12 guage oxygen sealed speaker wires all around

dB rating? not sure yet but will try find out some time soon

what a list.

Ive never tried to fit a 15'' let alone 2 of them.2guup has 2 12's that are a tite fit.i dont rate ur chances of fitting them.

All i could suggest is that you tear out the whole stock boot trim and start from there.make the spare tyre well one hole 4 the sub.but remember u have a huge magnet so make sure the metal in the boot dont interfere.hey! the second sub you could mount like a step.free air would be ur best option n use the boot as the box 4 da home made!!

thats a hektik install in that pic, team lets put an amp through a sub going too fast around a corner....

oh and if your car got impounded, take it to court, get some good legal representation and you might be suprised..

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Agreed, I've never seen a 260RS specific manual. As GTSBoy said it will mostly be stagea other than the engine loom https://www.hgeconsulting.com.au/stageaservicemanual.pdf
    • You'lll likely have to make do with R33 GTR for engine/tranny stuff, and Stagea for the body. I don't know that there's even been an actual diagram seen in the wild.
    • Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
×
×
  • Create New...