Jump to content
SAU Community

Dry Sump Setup Pics

widebody32

By widebody32,
in Engines & Forced Induction

 Share

Recommended Posts

Beer Baron Grand Master

Beer Baron

Posted
Posted
wouldnt happen to have a spare inlet manifold from the gt500 engine?

what will you do for me dave if I quickly steal that inlet next time i'm near one? I don't think nismo will give me one for love or money. and i've given them both over the years and they've given me some nice shit, but GT engine might push it! hope you get some inspiration from the pics though. :P

  • 1 year later...
BoostdR Mentor

BoostdR

Posted
Posted

here you go you picture hungry animals. threw in a few nismo engine pics to make up for the slowness.

NISMO JGTC RB26 DRY SUMP SET-UP:

picture789hx1.jpg

picture792gy8.jpg

picture786gt8.jpg

picture791vj9.jpg

picture788qt7.jpg

picture790ir1.jpg

now that i see it's on a little dolly i should have wheeled it home :w00t:

I see they aren't to stressed about harmonics....full counter weight no doubt

Beer Baron Grand Master

Beer Baron

Posted
Posted

yeah no real balancer as such, just a crank pulley to drive the water pump, alt and oil pump... everything would be finely balanced from end of crank to the clutch, not sure if the crank is full counter weight but it probably is.

bigmikespec Veteran

bigmikespec

Posted
Posted

Couple of things:

Have people who have done a full dry sump setup with a RB26 retaining the 4WD bothered take advantage of a shallower oil pan and lowered the engine? I can imagine it being a bit of a task especially to maintain the suspension and driveshaft geometry.

Is it necessary to run an oil restrictor to the head?

Hoping Brad (Risking) will comment on the first question.

bigmikespec Veteran

bigmikespec

Posted
Posted

You can't lower the engine much as the pan is not shallower where it goes over the A frame cross member and power steering. The sump box hangs in the abyss....

Matt

Good point; need to go under and measure.

Beer Baron Grand Master

Beer Baron

Posted
Posted

yeah given driveshafts still going through the sump/diff in the front it's not easy to drop the engine much if at all. plus if the car is already really low (using just adjustable shocks) then driveshaft angles are already fairly bad.

if you went to a remove front diff (like a hilux etc) arrangement then you'd be in business. but such a hassle.

Risking Grand Master

Risking

Posted
Posted

It's not hard to do at all.

I make the shafts with uni joints instead of constant velocities and put a good splined slip joint at one end to allow for length changes.

Never had a binding issue with lowered engines.

It also helps if you run a higher offset rim and move the hub outward utilizing longer front drive shafts. I think I know what mike has in mind hence the above suggestion he will understand.

The sump bulge gets cut off and critical parts of the diff casing need to be webbed into the pan.

Something I've also been stuffing with is a brace incorporated into the outter diff/sump flange which braces the diff casting to the block. It has seemed to help with the whole snapping diffs of with launching issue I used to have.

bigmikespec Veteran

bigmikespec

Posted
Posted (edited)

It's not hard to do at all.

I make the shafts with uni joints instead of constant velocities and put a good splined slip joint at one end to allow for length changes.

Never had a binding issue with lowered engines.

It also helps if you run a higher offset rim and move the hub outward utilizing longer front drive shafts. I think I know what mike has in mind hence the above suggestion he will understand.

The sump bulge gets cut off and critical parts of the diff casing need to be webbed into the pan.

Something I've also been stuffing with is a brace incorporated into the outter diff/sump flange which braces the diff casting to the block. It has seemed to help with the whole snapping diffs of with launching issue I used to have.

If you lower the engine you decrease your driveshaft angle which increases you track... so the proper way to do it would be to do what you suggested, you would not need longer driveshafts but the decreased angle might be an issue?

Why the move to uni's Brad? Sounds like a good idea RE: front diff casing.

Mr Baron: it is funny you mention removing the front diff. some mad fabricator in Sydney outlined plans for such a conversion :rolleyes:

Edited by bigmikespec
bigmikespec Veteran

bigmikespec

Posted
Posted

Not measuring the angle of the driveshaft it is hard to tell how much but it will vary. Want to get under and have a look this weekend. Also to check what Matt mentioned.

You are quite the argumentative type :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Ah ok. I seem to be mixing it like everyone else does so not sure what's happening. Will experiment with it more.
    • GTSBoy
      RB25det

      By GTSBoy · Posted

      Depends on what you mean by OK. First up, was this done cold or hot? Are they reasonably consistent? Yes, they are reasonably consistent. Could be better. But unless it has had a build at some point, it is a ~30 year old engine and you'd expect some variation. Some of the difference could also be in user technique Is it good compression? Well....not numerically, no. New they were >160 psi. The one at 140 would be fine, in that context. If they were all ~140, you'd be reasonably happy. But the one that is @120 is twice as far down from the original numbers as the one @ 140. But.. (again)... technique can play a part in the absolute magnitude of these numbers, and the quality/state of repair/accuracy of the pressure gauge is not known. In the context of the above, the compression tester that was used last on my car is regularly compared to a known good pressure gauge. Not calibrated, exactly, but compared to a reference instrument that is not used for any other purpose, so cops no abuse. So we can trust the measurements off that tester. But another tester in the same workshop wasn't being compared against the standard and was reading a good 30ish psi lower. When you're reading 100 psu but the engine is really doing 130, you can make bad decisions.
    • GTSBoy
      Steps to DIY sanding car back ready for respray....

      By GTSBoy · Posted

      More likely from tiny bubbles in the filler/putty. Maybe be less aggressive when mixing it. Perhaps invest in a vacuum chamber to pull the air bubbles out?** **I don't know if this is a thing for body filler. I see hardcore epoxy makers degassing their mixed resin on the regular.
    • GTSBoy
      ER34 4Speed Auto 25DE Speed Sensor

      By GTSBoy · Posted

      IIRC, the speedo on these is fed from the sensor in/on the snout of the diff.
    • funkymonkey
      R32 Nostalgia

      By funkymonkey · Posted

      They were. I bought the AWD for experimenting but racing it would disqualify or disadvantage me from a few race classes. Def getting a FWD for racing.
×
×
  • Create New...