Jump to content
SAU Community

Recommended Posts

Hi all,

Im looking to get my first Skyline so I went to Power Road Car Sales on sat afternoon and came accross this great looking Series II Skyline Its done 84,000kms, comes with 17" nismo wheels that are apparently worth $3000 (he said its a double wheel and it can be repaired) no Idea what he's talking about but it looks cool :) Its going for $18,000 inc road worthy, stamp duty and all that other rubbish.

Its got a scratch on the front bumper, rear bumper and the left hand light lense is a bit worn. They said that they will fix all of that when I get the car and the only reason they show the car like that is because they want you to see what it looks like straight from japan.

I asked the guy If it has had a compression test etc.. and he said it has its getting 20 psi on all cylinders (I dont know if thats good or bad) but if it has done all those tests is there supose to be paper work to prove it?

its got service records from japan too.

So what do you guys think of this?

Is it really worth $18,000, my budget was $15,000 but this car just looks so good.

post-32024-1160874320.jpg

post-32024-1160874332.jpg

post-32024-1160874340.jpg

post-32024-1160874358.jpg

post-32024-1160874367.jpg

post-32024-1160875786.jpg

Edited by gargantua
  • Replies 55
  • Created
  • Last Reply

Top Posters In This Topic

isnt 20 really low? arnt they spose to be around the 130+?

nice car. but really think u should negotiate on that price. might want to check out the for sale section people are selling from 15k!

and those km's prob arnt legit anyway lol

hanyou its done 84 not 20, so you guys reckon 84,000kms is BS? how so?

what about the compression thing is 20psi good?

just go by the general condition of the car/engine , km don't mean anything.

Compression test on a good engine should give results somewhere between 150-170psi and all cylinders should give fairly similar numbers. see this thread for example:

http://www.skylinesaustralia.com/forums/in...=136725&hl=

So first of I would be asking to see the results of the compression test as 20psi isn't correct. Also find out what he means by "he said its a double wheel and it can be repaired" if one or more of the wheels are buckled even though they can be fixed it's a major pain in the ass as fixing them doesn't always help that much, normally the steering wheel will vibrate round 80-120km/h depending on how bad it is.

As for the k's completley ignore them, they are never correct. Look at general wear and tear on the car, drivers seat on the door side, carpet around the clutch and accelerator pedal, the plastic around the bin in the drivers door arm rest, the material on the inside of the bonnet and the condition of the paint on and around the engine I always find are good indications of the cars use.

Otherwise car looks good, just do some bargning to get the price down a bit :)

Interloper how do I tell if the engine is in good condition? I dont know much about cars. I like Atreyu car. http://www.skylinesaustralia.com/forums/in...=131922&hl=

Is Atreyu's car in good condition? Ive told my dad about Atreyu's car but he thinks the car has been thrashed. Ive told him we can go check it out at a performance mechanic but he still dosent trust it.

20 psi is not good. 120psi is also not good so perhaps the salesman has no idea. Always take your car to a 3rd party for inspection. What Kyle has mentioned above is good info.

With that mileage, and that damage the car is simply overpriced.

Also, at risk of offending your dad, sounds like has doesn't have much of an idea as well if he can tell a car is "thrashed" from a few photos. Get an RACV inspection on any car you want if you aren't mechanically minded. An example, I have a 94 GTS25t I have run on the track. It's now twin turbo and has so many improvements it would take too long to list them and I'm about to rebuild the engine again and the gearbox syncros before doing a few more track days. I'll be selling it for a dedicated race car instead so you could say, yes, it has been thrashed and will continue to be thrashed around the track, but also lovingly and expertly maintained by a serious racer who just happens to be a very good mechanic and a mechanical engineer. Attention to detail is the difference and it will be so much more than an 8-10yo car that has been grannied around by some sook with a degree in hair product. Hope that offers some perspective.

I think you would do much better with a private sale and Atreyu's sounds good if that is more what you are after.

Interloper how do I tell if the engine is in good condition? I dont know much about cars.

the compression test is a good place to start also do a leakdown test to reveal any problems. Also don't use racv, go to a performance mechanic who knows what to look for and what he's doing. I went to racv a few years ago and i was very dissapointed :) (plus they charge $320 for an inspection)

maybe he meant the difference between max and min was 20....which would make more sense.

instead of debating just ask him for the results...and yes its if it is 20 you can easily tell with a quick drive...it will be farked.

milage is bs...you can get clusters from Japan and ebay aus easily...cost me less than $100 for a 74,000km one And the service reocrds are a bit dodgy IMO also...doens't mean anything unless u can check it.

By double rims he would have meant "two piece rims" that is it is made from two separate pieces, the round bit with the tyre on it and the bit that attaches to the car.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Lets say I wanted to buy this, specifically for this purpose. How do I actually perform the function. Can I still buy a Consult-1? Am I about to be burned by the fact my car is a 2000 model Series 2 R34 and thus will be some stupid other system? Do I just need this -> https://obd2australia.com.au/product/nissan-consult-14-pin-to-usb-ddl-diagnostic-interface-with-ftdi-ft232r-chip/ And with what software?
    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
×
×
  • Create New...