Jump to content
SAU Community

Recommended Posts

Hi all,

Im looking to get my first Skyline so I went to Power Road Car Sales on sat afternoon and came accross this great looking Series II Skyline Its done 84,000kms, comes with 17" nismo wheels that are apparently worth $3000 (he said its a double wheel and it can be repaired) no Idea what he's talking about but it looks cool :) Its going for $18,000 inc road worthy, stamp duty and all that other rubbish.

Its got a scratch on the front bumper, rear bumper and the left hand light lense is a bit worn. They said that they will fix all of that when I get the car and the only reason they show the car like that is because they want you to see what it looks like straight from japan.

I asked the guy If it has had a compression test etc.. and he said it has its getting 20 psi on all cylinders (I dont know if thats good or bad) but if it has done all those tests is there supose to be paper work to prove it?

its got service records from japan too.

So what do you guys think of this?

Is it really worth $18,000, my budget was $15,000 but this car just looks so good.

post-32024-1160874320.jpg

post-32024-1160874332.jpg

post-32024-1160874340.jpg

post-32024-1160874358.jpg

post-32024-1160874367.jpg

post-32024-1160875786.jpg

Edited by gargantua
  • Replies 55
  • Created
  • Last Reply

Top Posters In This Topic

isnt 20 really low? arnt they spose to be around the 130+?

nice car. but really think u should negotiate on that price. might want to check out the for sale section people are selling from 15k!

and those km's prob arnt legit anyway lol

hanyou its done 84 not 20, so you guys reckon 84,000kms is BS? how so?

what about the compression thing is 20psi good?

just go by the general condition of the car/engine , km don't mean anything.

Compression test on a good engine should give results somewhere between 150-170psi and all cylinders should give fairly similar numbers. see this thread for example:

http://www.skylinesaustralia.com/forums/in...=136725&hl=

So first of I would be asking to see the results of the compression test as 20psi isn't correct. Also find out what he means by "he said its a double wheel and it can be repaired" if one or more of the wheels are buckled even though they can be fixed it's a major pain in the ass as fixing them doesn't always help that much, normally the steering wheel will vibrate round 80-120km/h depending on how bad it is.

As for the k's completley ignore them, they are never correct. Look at general wear and tear on the car, drivers seat on the door side, carpet around the clutch and accelerator pedal, the plastic around the bin in the drivers door arm rest, the material on the inside of the bonnet and the condition of the paint on and around the engine I always find are good indications of the cars use.

Otherwise car looks good, just do some bargning to get the price down a bit :)

Interloper how do I tell if the engine is in good condition? I dont know much about cars. I like Atreyu car. http://www.skylinesaustralia.com/forums/in...=131922&hl=

Is Atreyu's car in good condition? Ive told my dad about Atreyu's car but he thinks the car has been thrashed. Ive told him we can go check it out at a performance mechanic but he still dosent trust it.

20 psi is not good. 120psi is also not good so perhaps the salesman has no idea. Always take your car to a 3rd party for inspection. What Kyle has mentioned above is good info.

With that mileage, and that damage the car is simply overpriced.

Also, at risk of offending your dad, sounds like has doesn't have much of an idea as well if he can tell a car is "thrashed" from a few photos. Get an RACV inspection on any car you want if you aren't mechanically minded. An example, I have a 94 GTS25t I have run on the track. It's now twin turbo and has so many improvements it would take too long to list them and I'm about to rebuild the engine again and the gearbox syncros before doing a few more track days. I'll be selling it for a dedicated race car instead so you could say, yes, it has been thrashed and will continue to be thrashed around the track, but also lovingly and expertly maintained by a serious racer who just happens to be a very good mechanic and a mechanical engineer. Attention to detail is the difference and it will be so much more than an 8-10yo car that has been grannied around by some sook with a degree in hair product. Hope that offers some perspective.

I think you would do much better with a private sale and Atreyu's sounds good if that is more what you are after.

Interloper how do I tell if the engine is in good condition? I dont know much about cars.

the compression test is a good place to start also do a leakdown test to reveal any problems. Also don't use racv, go to a performance mechanic who knows what to look for and what he's doing. I went to racv a few years ago and i was very dissapointed :) (plus they charge $320 for an inspection)

maybe he meant the difference between max and min was 20....which would make more sense.

instead of debating just ask him for the results...and yes its if it is 20 you can easily tell with a quick drive...it will be farked.

milage is bs...you can get clusters from Japan and ebay aus easily...cost me less than $100 for a 74,000km one And the service reocrds are a bit dodgy IMO also...doens't mean anything unless u can check it.

By double rims he would have meant "two piece rims" that is it is made from two separate pieces, the round bit with the tyre on it and the bit that attaches to the car.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The team at OBD2 Australia are pretty good, shoot them an email and ask them. I've dealt with them before for work stuff. I'd be shocked if it didn't work, so long as Consult can activate the ABS. But you might need to use KLine for it which would be the stopper, as I don't think that piece does KLine comms.
    • Yeah and hence my ghetto way of slamming the brakes, get the ABS to cycle, rebleed seems to be a sensible workaround.
    • Hey! Happy to help. Nothing inherently wrong with the adapter, it's more so with Brett Collins himself. He gave me a lot of incorrect information when I was in contact with him and was extremely rude when I challenged him. He stated I could not use any aftermarket twin plate clutches except for his own, not to use the dush shield, bla bla bla and it was all BS.  Collins stated to cut roughly 14mm's off the housing, I took off 15mm to make room for the dust shield. I would confirm with whatever adapter manufacturer you're using. 
    • There's plenty of OEM steering arms that are bolted on. Not in the same fashion/orientation as that one, to be sure, but still. Examples of what I'm thinking of would use holes like the ones that have the downward facing studs on the GTR uprights (down the bottom end, under the driveshaft opening, near the lower balljoint) and bolt a steering arm on using only 2 bolts that would be somewhat similarly in shear as these you're complainig about. I reckon old Holdens did that, and I've never seen a broken one of those.
    • Let's be honest, most of the people designing parts like the above, aren't engineers. Sometimes they come from disciplines that gives them more qualitative feel for design than quantitive, however, plenty of them have just picked up a license to Fusion and started making things. And that's the honest part about the majority of these guys making parts like that, they don't have huge R&D teams and heaps of time or experience working out the numbers on it. Shit, most smaller teams that do have real engineers still roll with "yeah, it should be okay, and does the job, let's make them and just see"...   The smaller guys like KiwiCNC, aren't the likes of Bosch etc with proper engineering procedures, and oversights, and sign off. As such, it's why they can produce a product to market a lot quicker, but it always comes back to, question it all.   I'm still not a fan of that bolt on piece. Why not just machine it all in one go? With the right design it's possible. The only reason I can see is if they want different heights/length for the tie rod to bolt to. And if they have the cncs themselves,they can easily offer that exact feature, and just machine it all in one go. 
×
×
  • Create New...