Jump to content
SAU Community

Recommended Posts

CAn you elaborate on this GT3071R

What size ex. A/R should i use?

What is it rated at? I think 500hp

What its response like and full boost rpm?

Do i need a custom dump? How much?

How much is this turbo cost? Best price was $1750 on ebay

Is anyone running this turbo on a RB25? If yes please state mods and power made.

FOR F@#$%K SAKE! :O

Does anyone know the ANSWER to any of the above QUESTIONS???

Ahhhhhhhhhhhhh much better now.... :(:(:(

Link to comment
https://www.sau.com.au/forums/topic/139448-garrett-gt3071r-info/
Share on other sites

I have one with a .7 cover and a RB25 Turbo read ground out to fit.

Comes on full boost at 3200rpm in second.

I'd go for the .6 compressor cover - Your max efficiency will be on lower boost. With the .7 compressor cover, max efficiency is at about 22psi - which is too much for a standard internal RB25.

So yeah, .6 compressor cover, and about 16psi and you should see over 250rwkw easily. If you want a bit of lag and heaps of top end, go for the .86 rear.

just make sure they don't sell you one with a to4s compressor wheel.

:D

Talk to Slide off this forum! i just bought one for my rb25 & its being put on as we speak! its got the 0.82ar plus im putting in poncams etc so it should be fairly responsive!

:laugh:

Al_R33 I thought you had a 3076 as well???

i had 3071 on my rb20 in both .86 and .64 housings.

.86 reached 260rwkw @ 21psi, boost could be controlled lower, laggy as crap eg no boost at all until low3 full boost @ low 5rpm

.64 reached 257ewkw @ could not get boost below 22psi. 500rpm better.

Lots of fiddling to fit - not worth it IMO

Be careful peoples , not all Garrett GT3071R's are created equal .

Firstly the GT3071R-WG . Dog turbo becauses it uses the cropped GT30 turbine in a .64 or .86 GT28 IW exhaust housing . Failed concept , doesn't work acceptably and should not be on the market .

Rule (1) with GT3071R turbos , if it has a T25/28 flange (which is wrong for Skylines) its looking for a victim .

Secondly the R E A L GT3071R W I L L have a T3 flanged exhaust housing , not any old T3 flanged housing but a real Garrett GT30 type exhaust housing . The R E A L GT3071R will have an unmolested 60mm GT30 84 trim turbine , approx 60 x 55 mm dimensions . This turbine and its native turbine housing family are the critical components that make this turbocharger WORK properly . Its a production derivative of the Garrett competition specific TR30R turbocharger .

Do a few searches on Garrett GT3071R and wipe anything ending in WG or -WG . You'll find it at ATP Turbo in the US amongst other places . You'll also find it at turbobygarrett.com but only in the turbo comparison sheet . Scroll down the table to the last of the three GT3071R's , I think they quote is as the highest power capable variant at around either 440 or 450 Hp . Even search this site , at least one person here is using one on an RB20 .

Lastly , don't forget that genuine Garrett GT30 integral wastegate housings (T3 flange) are now available in .63 .82 and 1.06 AR ratio .

It it were me I'd read the turbos ID tag carefully if searching for one of these , it should say CHRA no 700177-0023 like that Garrett comparison sheet tells you . Don't accept any moron telling you that those numbers are unimportant or minor variations are insignificant .

Cheers A .

Thanks 'discopotato03' ill quote this CHRA no700177-0023 when i purchase the turbo.

While we are on the topic if a particular turbo is rated at 500hp. Is that the figure it can provide at the flywheel or the rear wheels?

Will this turbo clear the block and chasis? Will it need a spacer?

Hi Nabil , it seems the power figure of the turbocharger is worked out from its maximum compressor flow in pounds of air per minute . A conservative rule of thumb is 10lbs per hundred Hp so 50lbs of air to 500Hp .

No turbocharger manufacturer can work out how much Hp their turbo will make on any engine because there are so many variables . Its up to the person developing an engine to make it swallow as much air as possible and vent exhaust gas at a sufficient rate to not suffer reversion and pumping losses .So basically a 500Hp capable turbo may not get you 500 from your engine , it will depend on how well its developed .

Cheers A .

grim32,

Have you had yours tuned since mr squiggle had his way with it?

Nah i havent, i did notice on the last power run it was starting to roll out a cloud of smoke but didnt think to much of it at the time. A week or so later i saw it was blowing a heap of oil out the dipstick so i let it sit in the garage for a while. Recently i did a comp test and found no.2-6 were at 125psi but no.1 was only at 75psi. Lifted the head and no.1 bore was glazed up and there were detonation marks on the top side of the piston (melted). (Whoops accidently mis set the boost on the dyno and ran 30psi for a sec or two)

I decided to ditch the 20 for now and picked up a cheap R32 RB25de which i should have back in soon, i plan to run it at 15psi and see how it goes, if bad RB30DET here i come.

Bugger. :D

The 25 will work well with the turbo you have but the 30 may choke a little.

15psi through the 25 head will be roughly the same air flow as ~19-20psi through the 20. Throw your stock turbo RB20 cams into it, better suited for turbo. :)

The RB25 n/a springs actually are the RB20det springs.

Most experience valve float at higher boost levels as the rb25de valves are larger, so they really need a better spring.

But a lot have had good results when shimming their springs so that may be a cheap way out if your only looking to run lowish boost, which 15-17psi is. :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
    • Well this shows me the fuel pump relay is inside the base of the drivers A Pillar, and goes into the main power wire, and it connects to the ignition. The alarm is.... in the base of the drivers A Pillar. The issue is that I'm not getting 12v to the pump at ignition which tells me that relay isn't being triggered. AVS told me the immobiliser should be open until the ignition is active. So once ignition is active, the immobiliser relay should be telling that fuel pump relay to close which completes the circuit. But I'm not getting voltage at the relay in the rear triggered by the ECU, which leaves me back at the same assumption that that relay was never connected into the immobiliser. This is what I'm trying to verify, that my assumption is the most likely scenario and I'll go back to the alarm tech yet again that he needs to fix his work.      Here is the alarms wiring diagram, so my assumption is IM3A, IM3B, or both, aren't connected or improper. But this is all sealed up, with black wiring, and loomed  
    • Ceste, jak se mas Marek...sorry I only have english keyboard. Are you a fan of Poland's greatest band ever?   
×
×
  • Create New...