Jump to content
SAU Community

Devastating :(

Jamezilla
 Share

Recommended Posts

Jamezilla Grand Master

Jamezilla

Posted
Posted

Car got broken into in my driveway last night. Lots and lots of things stolen. Lots of things smashed to steal things.

I am very very unhappy :D

All the Apexi gear was taken (RSM, AVCR, boost guage) so if anyone (particularly VIC members) hears of these and other things for sale in a dodgy manner - notify the police to check it out.

Link to comment
https://www.sau.com.au/forums/topic/13959-devastating/
Share on other sites
Al Grand Master

Al

Posted
Posted

Really pissed to hear that mate.;) What f@rken a55ho1es!!!

Hope you get your car back to scratch and that the insurance doesn't stuff you around!!

Hate to say this, but sounds like some inside knowledge. How did they know that your alarm is not equiped with some kind of motion detector.

The reason the alarm did not go off is probably due to a lack of motion/infra red sensors. If they didn't open the doors or try to start the car the alarm could not detect the theives. If you wish to not install any motion detectors (as they are known to sometimes false alarm) an idea to to install a 'trigger switch' (similar to the ones in your doors or under your 'hood' and 'boot' lids) in your 'center console' and 'glove box';) . A theif will almost definately look in these areas for goods, and once they are opened they break the electrical circuit and the alarm will trigger. :uh-huh:

Link to comment
https://www.sau.com.au/forums/topic/13959-devastating/#findComment-280059
Share on other sites
Roy Grand Master

Roy

Posted
Posted

... bunch of savages. I dont understand why they take things like the AVC-R, its useless unless they pop the hood and take the MAP sensor, wiring and solenoid valves as well.

The hide of people, the courts have a lot to answer to, theft like this cost insurance companies $$$, owners heartache, and often these people are known to Police and have committed similar offences before.

... anyone read the comic PUNISHER when they were younger?

Anyways, hope insurance does the right thing by you, and your back motoring soon.

... and AL, is this is DIY job, is it a matter of a few $$$ at Jaycar then wiring them in series with those for the doors???

Link to comment
https://www.sau.com.au/forums/topic/13959-devastating/#findComment-280109
Share on other sites
Gester Collaborator

Gester

Posted
Posted

Its weird how most people who have their car's broken into or the ones we here about on here are from Sydney. Is Sydney really this bad? Looking at performance forums almost 95% of the stolen posts are from people in Sydney.

Surely this stuff has to happen elsewhere? I know it would but why does Sydney have so much more car theft then other cities?

Link to comment
https://www.sau.com.au/forums/topic/13959-devastating/#findComment-280670
Share on other sites
Jamezilla Grand Master

Jamezilla

Posted
  • Author
Posted

Thanks all for your support.

I have spoken to the main Apexi distributers here in Melb asking them to notify police if anyone comes in wanting the 'extra' parts of the AVCR and RSM.

Re: serial nos - I don't have any of the ones from the car stuff - as they were on the car already. The other personal items taken had serials - have been given to police.

The GTR-88 plates were taken. If you see them driving around - call the cops.

Re: alarm - I have no idea how they got around it. Really really f*cked. :P

Quite upset about it all. Will keep you posted.

Thanks again

james

Link to comment
https://www.sau.com.au/forums/topic/13959-devastating/#findComment-280765
Share on other sites
Al Grand Master

Al

Posted
Posted

Jamezilla

Do you have motion/infra red sensors in the car? With a car like that, i would seriously consider an upgrade in car security.

Really sorry to read about loosing all those sentimental goods. A car can be fixed/replaced, but goods that have alot of personal value are priceless. One thing that wasn't stollen were your memories, sounds a little corny, but your gf will always be in your mind and heart.

Link to comment
https://www.sau.com.au/forums/topic/13959-devastating/#findComment-282041
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      And if you have to drill the oil block, then just drill it for 1/4" and tap it BSP and get a 1/8 to 1/4 BSP bush. The Nissan sender will go straight in and the bush will suit the newly tapped hole. And it will be real strong, to boot.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      No it doesn't. It just needs an ezy-out to pull that broken bit of alloy out of the hole and presto chango - it will be back to being a 1/8" hole tapped NPT. as per @MBS206 recco. That would be for making what you had in alloy, in steel. If you wanted to do just that instead of remote mounting like @Duncan and I have been pushing. A steel fitting would be unbreakable (compared to that tragically skinny little alloy adapter). But remote mounting would almost certainly be 10x better. Small engineering shops abound all over the place. A lathe and 10 minutes of time = 2x six packs.
×
×
  • Create New...