Jump to content
SAU Community

Calder Night Drags - Fri 27th Oct - Cancelled

Al

By Al,
in Archived Events

 Share

Recommended Posts

Al Grand Master

Al

Posted
Posted

Would like to have an SAU drag night at Calder Park Rwy, on Friday night, the 27/10/06.

If we enter as a club there is a $10 dicount for entrants, and we get to park with the "comp cars", and possibly get more runs. Not sure if there will be any dicounts for spectators, but will ask.

To enter as a club, i need names and car model from people that are definately interested. So post up if you intend to come and have a heap of fun. :)

NOTE: This is not an "offical" SAU VIC event, but i still class all SAU forum members as a club.

Competitor list:

- Alan Calleja R33 GTS-t

West Grand Master

West

Posted
Posted
Would like to have an SAU drag night at Calder Park Rwy, on Friday night, the 27/10/06.

If we enter as a club there is a $10 dicount for entrants, and we get to park with the "comp cars", and possibly get more runs. Not sure if there will be any dicounts for spectators, but will ask.

To enter as a club, i need names and car model from people that are definately interested. So post up if you intend to come and have a heap of fun. :)

NOTE: This is not an "offical" SAU VIC event, but i still class all SAU forum members as a club.

Competitor list:

- Alan Calleja R33 GTS-t

Can NON MEMBER run since its not an offial SAU event?

Russman Grand Master

Russman

Posted
Posted

Good idea Al.

It sucks coming back up the gravel lane. The 'comp' cars get it easy returning on the track.

It's about time Bob Jane spent some money to fix it up a bit I reckon!

I can't make it thought cos I'm in perth.

Hope you all enjoy it.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Komdotkom
      R32 Gtst - Track Car

      By Komdotkom · Posted

      Good luck on the weekend mate
    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...