Jump to content
SAU Community

Recommended Posts

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

I will take any or all of these if you can ship to Sydney, let me know how much you'd like:

Right headlight

Washer bottle (water washer you mentioned above?)

Radiator overflow bottle

Thanks!

HI Guys, i just have Wreck a skyline R33 GTST 96 model all parts are for sale :

-complete motor $2400

-Set of coil over like new $800

-Set of rim with no rubber $300

-RH front door shell only $100

-RH front glass $50

-RH front guard $80

-Front huh $150

-Rear complete brake $350

-Two front seat and rear seat $200

-Feul tank and pump $200

-Center consor $30

-Center surround that go around the dash $80

-Brake master & boost cyclinder $150

-Water washer $20

-That all i can think of at the moment but will update some more list on the weekend and also some picture as well so you can see the parts .You can alway pm me for the parts that you need just incase i do have it and i didnt listed.

-

do u have a gear box

and where u located

JimX: as i am in sydney just want to let you know the RH head light is S1 if you still want the head light for the lots will be $130

or $30 with out the head light.

Yes I need a series 1 headlight so that is perfect :whistling: I can come around and pick up everything tomorrow afternoon/night if that's ok?

hey, have you got the regulator for the RH doors? If so. i'll take the whole door. I can go pick up immediately whenever your free. Please PM phone number if you have.

Thanks.

r32-25t- no front enforcement bar

The Mafia- the grill i got is like a gtr grill .

BLACK WARRIOR- it a GAB coil over like new that all i know.

STRYKR 33- i only got the switch left and the door shell no motor

most people that pm me i have return your pm.

Edited by playergtr
The Mafia- the grill i got is like a gtr grill .

What car was it originally fitted to? A Series 2?

Can I please have pics? - paceys[at]gmail.com

Edited by The Mafia
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...