Jump to content
SAU Community

Workshop Drops Lotus Elise (with Pix)

sigsputnik

By sigsputnik,
in General Automotive Discussion

 Share

Recommended Posts

racsov500 Grand Master

racsov500

Posted
Posted (edited)
uhh no

notice how on the lotus elise, the front wheels are removed, and the 350z the back wheels are removed

im guessing these mechanics dont quite grasp the basic concepts of gravity

I was talking about weight balance

its about 70/30 or 60/40 on a hoist, on a normal frount engine car the middle is about halfway down the drivers door, thats how it is at my work

looks like thyve put it on the hoist as a normal car

oh and with the 350z, it would have been balanced fine until they took the rear cradle out

weve had cars at work with no rear ends in them and havent had any problems

again its just about making sure youve got the centerpoint of balance right

Edited by racsov500
mad082 Grand Master

mad082

Posted
Posted
That mechanic in the picture looks like a shocked version of Chopper Read

hahaha

the owner comes in and sees the car hanging off the hoist and starts crying. chopper comes over and says...

"harden the f**k up!"

boot_it Enthusiast

boot_it

Posted
Posted

have a look at the hoist they are using (a old school hydrallic system) that they stop making in the 1970s and the pads look f**ked

but in the mechanics defence there not as easy to put up as ppl think that have a full metal pan under neath the vehicle any my workshop was a aurthised lotus dealer and they never put them up on a 2 poist hoist (they always went on the 4 post hoist that had 2 full beam arms the lenght of the 4 post hoist that had pads that slide down the beams so u could pritty much pick the vehicle up in any spot and if it did fall it would only fall 3in on to the beams

but when i did a quick stint at jaguar (porshe had just moved workshops)and the mechanics were telling me that the stupid apprentices were working on porshes they would always put the vehicle on the hoist in the wrong spot so when the motors were dropped out the car would be front end heavy and would start to topple nose down off the hoist and ppl would have to hang off the back of the porshe to even the weight so they could drop the car back down on the ground

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      "Cheap" bolt on turbo on RB25DET NEO

      By Murray_Calavera · Posted

      The fab work can be as simple as a couple of silicon hoses and clamps to the factory piping. 
    • joshuaho96
      "Cheap" bolt on turbo on RB25DET NEO

      By joshuaho96 · Posted

      Just sounds like either way you need to do some fab work to get everything to fit, so why limit yourself at that point? If the GCG high flow option is zero effort in and out swap though I'd probably do that. It's almost certainly lowest risk, lowest cost, etc. The HKS GTIII-RS option that Kapr mentioned is laughably expensive for what it is, they charge the exact same for two turbos on the RB26 so their margins are off the charts on that thing.
    • GTSBoy
      "Cheap" bolt on turbo on RB25DET NEO

      By GTSBoy · Posted

      Intake manifold is not a part of the issue. The turbo bolts to the exhaust manifold. That is easy. But close your eyes and picture the physical situation. That is a T3 flange on the manifold and a T3 flange on the turbo. As long as any new turbo has a T3 flange on the exhaust housing, that exhaust housing will bolt to the exhaust manifold. This places the exhaust housing in the same place as the stock one. But now move your mental attention a little further forward. The location of the compressor housing is set by the length of the turbo's core. The stock turbo had a long core. Let's say that it is..... 100mm long. So that would place the compressor housing 100mm forward of the exhaust housing. But a highflow, might well have a centre core that is shorter. Let's say that it is only 70mm long. Now the compressor housing will be 30mm further back in the engine bay than the stock one. This DOES move the turbo's compressor outlet backwards. It also moves the compressor's inlet backwards. You will very likely have to do some work to both the inlet and outlet piping to make everything connect again. I am not say this to make it out to be a bigger deal than it is. I am just pointing out that "bolt on" is sometimes not quite bolt on. The highflow from GCG that Murray linked above (https://gcg.com.au/turbo-charger-upgrade-skyline-gtst-2iu-xtrgts-s1.html ) uses a core that is the same length as the stock core, and so does not require this extra work. It will look very much like the stock turbo. No-one uses GTR turbos of any flavour (stock, or aftermarket) in a single turbo application on RB20/25. It's not a thing. Yes, people have been putting on GT3076, GTX3076 (and bigger and smaller versions of those) and G30s (of various sizes) onto RB20/25 since forever. But these are not "bolt on". Everything except the 4 bolts to the exhaust manifold change with these. And genuine Garretts are expensive. Non-gen, like Pulsar, etc, are cheaper, variously as good or nearly as good. But still not bolt on. No-one in the right mind would pay for an HKS turbo. Not in this modern day and age. Well, yes, the GCG highflow. You could ask HG what he can do to make the compressor housing sit in the original location. There are surely others doing highflows around the world. And some of the eBay/Temu ones (as reported by Dose) work and don't die. Bit of a lottery though. I would send your turbo to GCG (here in Oz) to be highflowed if you want a trivial no-extra-work option. But seriously, the work required to change inlet and outlet piping is not that hard. That's a boost control problem, not a turbo problem.
    • Kapr
      "Cheap" bolt on turbo on RB25DET NEO

      By Kapr · Posted

      Thank you all for the replys 🙂 I know that intake would be different but that is one pipe at it is not that hard to get(custom one). I meant mainly bolt to the stock manifold and the turbo elbow. I looked and many sites/forums but they are just "old" with some old HKS turbos from GT-R i guess? What about some Garrets?  Or any other turbo? Is there even a turbo which i can just bolt on? 😄 And yeah i know about that new HKS but that is like 2000k USD without taxes/shipping in here   Iam getting a touch up tune but my "problem" is that on the "not" hot day iam getting peaks around 0,9 bar...and when it was around 15 Celsious i saw peak around 1 bar which is just too much for stock turbo. And of course turbo is old and i like to get some new one for a piece of mind 🙂 
    • GTSBoy
      new here

      By GTSBoy · Posted

      I'm working on the assumption that our friend Jasmine here is a Russian (or, possibly Ukrainian) spammer/spambot, based purely on the number of such that I have been having to neuter in the last few weeks. IP address for the OP above was in WA. But that could have been via VPN. Posting at quarter to 4 in the morning is a good sign of being from somewhere in Europe. The last Jasmine that I kicked in the cooch was IP addressed in Ukraine. Even that could have been via VPN, and the bitchbot could have been from Russia, Serbia, China or anywhere. Regardless, was a spambot, so I killed it with fire. The fact that our new friend Jasmine here did not respond in any way to my tart query strongly suggests to me that this OP was just the establishment phase of a user able to be activated for spamming in a week, or 3 or 10.
×
×
  • Create New...