Jump to content
SAU Community

Recommended Posts

  • Replies 231
  • Created
  • Last Reply

Top Posters In This Topic

Would be interesting to see how much KW you pick up with a larger exhaust dump pipe from the turbo ,

any one know if they run the larger VG30 ex housing on the rb25engine for the Siding turbo up grade ?

Looks good should be happy with $$ you spent on the turbo

My boost was holding perfectly at 16psi with the turbotech controller. I amso have a 3" split dump from the turbo back to the cat.

Cubes, Live edit can be used as a good ground for a base tune but is not accurate down to 1/2 of an afr by any means, especially when you start changing the injector size.

but it is a good starting point.

CEF11E,

Live-edit... How well does the afr display reflect real world afr's?

In most cases not even remotely close for the open loop stuff.

The closed loop stuff should be fairly close assuming the inj and maf are calibrated correctly.

Well I have placed an order with Slide, on a recent trip to the sunny Gold Coast I left a VG30 turbo with him to be MAX FLOWED.

When it comes back it's going on my new L28ET engine, which will be interesting, or hoping so.

Will let you know what it looks like, as he says it will be back by about 26th November.

Cheers, D

Got my Sliding Performance highflow for a AWD RB25det Stagea, received just now

Looks wild !!! Been bored-out to the max! Getting installed on Monday, dont know when the safc & sitc will be re-dyno tuned tho. So I'll keep it under 10psi until its tuned.

Hopefully get the exhaust cam gear wheel installed at same time. And my brake upgrade, time permitting.

this is going to sound like a dumb question (and it may have been answered in the middle few pages. i read the first 2 then skipped the rest), but what does it hit full boost by on the rb20, and what does the stock rb20 turbo hit full boost by?

turbotech boost controller = designed/sold by a guy on these forums for about $35... also retailed by DrDrift

works a bit differently (Better) than a bleed valve... brings boost on faster etc.

sounds great, i want one.. who do i contact to purchase?

cheers

simon

look for one of my old threads called I found a good cheap boost controller for $22.

it is in the forcen induction section and there are about 100 pages of info on it :) the guys name is Mark and his email address is on the first few pages.

Cheers :)

I am working thru my spark issue and turns out I was wrong about the plugs I was using. I had a set of NGK BPR5EIX-11 plugs!!! supprised it didnt miss at 10 psi!

I have just bought the wrong plugs by accident... BCPR6EY-11 Do'H!

The plug height is shorter than the BCPR6ES. they are in the car untill the weekwnd when I will get the bloody correct plugs this time gapped to 0.8.

lol No the rb20det turbo is off it has been running a vg30det turbo for some time. :)

The VG30 is better but still lacks.

These turbo's are cheap, but I really want to throw on an int. gate gt30 .82. and ram as much boost as I can (20 odd) in to it.

A gt35r would be nice but is a tad too laggy on the 3ltrs especially when they need a plenum to make them rev hard. (as we recently found out on a mates car)

BUT... I really am getting tired of driving a car that has a decent motor but crap turbo on it so it very well may see a vg30 max oversize slide turbo thrown on the side. See how things go. :)

I am currently having issues with coils but have had some more time to test.

I have leaned out the tune to 12:1 and put in new plugs and gapped them to 0.8 and am now running 18psi. after 1/2 hour the one of the coils starts to produce missfire so new coils are on the way but the car REALLY moves.

I would estimate there is at least an extra 20rwkw increase taking it to around 230~235RWKW and boost feels like it is coming on much quicker. it starts to get up and go at around 3600rpm.

this is still with the 2.75" exhaust. I really have to say this is a great turbo. I don't care if it is bush bearing, it is a better match to the RB20 than a lot of turbos that cost twice as much. I am really happy with the performance and have pushed the little RB20 as far as I think is realistic for a daily driveable car.

I couldn't be happier.

Cheers :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...