Jump to content
SAU Community

Recommended Posts

hey all

ill inform you about the crisis i went through

i was driving down one of the streets in wa...

I WAS HITTING 3 PSI in 3rd gear when i heard a loud pop noise on the drivers side...

just then all my light when on battery, oil level, water temp etc my power steering failed and my brakes woundnt work.... i then quickly pulled my car onto a back street and stop and tried starting it again... it started by then it would just turn off.... and it keep doing it.... it also is blowing out black smoke...

can some one help me and give me advise on what it can be please.......

cheers

jason

Link to comment
https://www.sau.com.au/forums/topic/144949-car-engine-blown-i-think/
Share on other sites

it started by then it would just turn off.... and it keep doing it.... it also is blowing out black smoke...

There's ignition, there's fuel.... Blowing black smoke indicates a gross inlet leak.

I ignored the 3psi fact after I read ----

power steering failed and my brakes wouldn't work
"Fuel pump or fuel lines. No fuel = no go!!!

Warning lights on, brakes and power steering is only from the engine not running. They all need motor running to work properly."

What he said!!!

it also is blowing out black smoke...

black smoke = plenty of fuel.

when my cooler pipe came off i was still able to drive for another few hundred meters until i could find a place to pull over.

but the symptoms are there for a cooler pipe. "it started by then it would just turn off.... and it keep doing it.... it also is blowing out black smoke..."

When it happened in mine after I put my front mount on the car puffed out a big cloud of black smoke and struggled to idle. It gave me a scare as it had never happened to me before. Popped the bonnet and found the hot pipe had come off.

Cheers

Chris

Edited by alphanumeric

and then when the pipe is put back on, just hope that the plugs aren't fouled!

that's what happened when i blew off a cooler pipe.. had to change the plugs to get it to run again... (they were due for a change anyway and i had them there to change that week)

I've had mine let go.. I think its let go on every one who works on their car some time or another.

I was in a rush to take the car for a spin with the new turbo on it. :P

Completely forgot to do up the ic pipe to cross over hose clamp. Started to accelerate lightly, it may have hit 5-7psi or so and BANG!!! nothing, no acceleration. I dipped the clutch the car lumped over for a sec and died.

Tried to start the car; it would start then stall, wouldn't even idle.

Popped the bonnet and saw the ic pipe sitting half in the rubber half out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...