Jump to content
SAU Community

Recommended Posts

PwrFC VS Microtech?

any experiences or opinions, plz post input

which is better , which runs better, is more cost effective versus adding more mods etc.

and for a Daily driver.. wouldnt it be better to actually keep the afm? for fuel consumption reasons, in different temperatures?.

Link to comment
https://www.sau.com.au/forums/topic/145451-pwrfc-or-microtech/
Share on other sites

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

Not really the results im lookin for..

I know there is LOADS of info on the PFC on these boards.. Not so much about the Microtech on a skyline though..

what i really want is a comparison. I mean.. the PFC was originally designed with Skylines in mind.. wasnt it?.. could be wrong there.. but also the microtech has good self learning features so ive been told,

so i need a comparison, cause im tryin to work out which route im going..

i mean i can get the PFC, get it tuned at pits or somethin, prob cost me 1600 total.

Or i can get the Micro, from Microtech to suit my rb25det, then fully tuned buy my tuners. for 2k flat.

just wondering.. is it better to spend the extra 400$. and i mean, wat if the PFC is better for the skyline..

so can anyone Compare the 2? and point out your reasons for the results.

Depends whether you want air flow readings or Air pressure, they both have their adv and dis but in reality it is what your tuner would prefer.

The microtech being Manifold Air Pressure sensor (MAP) is hesistant around zero pressure, this is a hard area to tune compared to a Manifold Air Flow (MAF) which can determine quite easy if it is flowing or not.

Depends whether you want air flow readings or Air pressure, they both have their adv and dis but in reality it is what your tuner would prefer.

The microtech being Manifold Air Pressure sensor (MAP) is hesistant around zero pressure, this is a hard area to tune compared to a Manifold Air Flow (MAF) which can determine quite easy if it is flowing or not.

Good point,

Yea tuner good with em, Might go with the FC, but hmmm, hard decision. will have to find a tuner for the FC . its a daily driver, not a race car.

Thanks for your comments guys! :D

Edited by silverbulletR33

I'm using a microtech LT-8. Crappy fuel economy, crappy cold start. Not such a fantastic ECU for a daily driver. Power FC is prolly the way to go as in my opinion microtech is more of a racing ecu. So yea, PFC is probably the go for you, except i have a thing against AFM's (don't know why, i just do).

www.nengun.com

www.ebay.com

Still plenty around, just have a look.

nengun doesn't have any in stock.. ebay ? you actually looked for an rb25 one? ZERO. The only ones that are around, are the ones that haven't updated their stock levels properly. When you ask 'no sorry, don't have that model anymore, have the others'

"plenty around" my ass...

had a microtech on my s1 33 gtst actually was the first in adelaide to have their 'plug n play' setup. in short it was very poor as a daily driver, mostly cause it did not have enough adjustment for cold start idle up etc. but as alredy stated, fine for a race/weekend only car. oh yeah and definately agree that your tuner is EVERYTHING when dealing in aftermarket ecu. my choice PFC :)

I have tuned quite a few of both, and unless it has 1000hp and the afm is casing a restriction, the pfc has many more features than the microtec, and will return better fuel economy/cold start/drivability with far less tuning. Most dyno shops can tune a pfc, and many have datalogit, if they cant, i wouldnt let them tune my car.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Block bump. $400. As above cyl 6 needs bore or sleeve.
    • I would think making the argument that the travel is limited by a spring flexing against a spring perch as "the same method". Later on in the document they do state that the spring can't bind on full bump travel and cannot come loose in full rebound travel as well. (which is all very sensible). The laws are actually pretty sensible and reasonable. It's just that the people who enforce and check them don't actually read them or know them accurately. "Oh, coilovers? Instant fail mate. Don't even need to look at it." - Guy who will be instantly reported by me. There is probably merit to people who do get defected for height also get defected for the suspension in that state that allows it. I did never consider the people who are complaining about coilovers being picked on are also running around at 50mm off the floor.
    • I think given SAU's knowledge of E85 we can strongly conclude that 10% ethanol in almost any situation is entirely fine. Almost all of the myths against E85 were overblown, let alone E10.
    • From your link See bold text, is this referring to damper settings, if so that may a issue for "some" inspectors, I cannot see aftermarket coilovers having the evidence that "must be available that its functional performance is equivalent to the original" Maybe just remove the adjustment knows and hope for the best???? Meh 5.2 Suspension travel In all instances, modifications to a vehicle’s suspension must ensure the integrity of the system and not compromise the ride quality. At least two thirds of the original suspension travel should be maintained in both directions (rebound (i.e. extension) and bump (i.e. compression)), and rebound must be limited by the same method used by the vehicle manufacturer or if this is not practicable due to the nature of the modification, an equivalent method. If an alternative method is used, evidence must be available that its functional performance is equivalent to the original.
    • They actually don't - They adhere to VSB14 rules just like Victoria. The rules are against CABIN adjustable height, and it quite clearly states that the height has to be within parameters. I asked the VASS engineer to confirm this when I got my car engineered and they refused to engineer the coilovers because they didn't meet the requirements for requiring engineering. (mine are height adjustable.) People "Not wanting to bother" with "Actually reading/knowing/adhering to the rules" should result in fines and immediately losing the ability to issue blue slips and/or RWC's in Vic.
×
×
  • Create New...