Jump to content
SAU Community

Recommended Posts

Guys, as titled, I need some assistance with a Grex oil cooler. The model I ordered should fit into the right inner fender. I guess that means the drivers side right? But all the pictures in the japanese instruction book refer to the passenger side? WTF is going on?? I am trying to fit the cooler in front of the factory BOV but I have never seen a cooler mounted there with the BOV's still installed. I wish I could read japanese. Can anyone shed some light?

Thanks for that. Grex make a number of different kits. They all have various length hoses depending on the coolers location. Has anyone fitted the grex cooler infront of the factory BOV's?

I'm not sure if its going to fit and my instructions are for the wrong location :happy:

I got a HKS oil cooler it goes on the passenger side , the lines run under the motor

I highly doubt you can fit it (any cooler) in front of the BOVs. mine is in the passenger side duct. mine is a grex kit also. the big one. and it just barely fits in the passenger side duct.

ive spoken with the guys at meridian motorsport about an oil cooler for my gtr and they say they have never fitted a cooler to the drivers side. they have always put them on the passenger side

i have a large one.

mines mounted horizontal (laid flat) here....

shot is from under. and its more over to the passenger side. left part is front lip

max temp today was 85c which was driving for a long time with a fair bit of hard driving (i went bush)

post-31456-1165569712.jpg

Edited by Angus Smart

I hav a grex cooler kit mounted in front of the blow valve on my 33gtr... i had to convert to greedy type r as the standard bov's would hav needed to be modified (re bracketed and chopped) to fit the cooler in place....

you know the inner fender probably refers to the area right in front of where the RHS front wheel arch is...

i.e the position where the GTSt ventilation slats for the SMIC are cut into the inner plastic guard on the passenger side, but on the driver's side...

so the cooler sits not against the front bar, but behind the BOVs nearer to the wheel well?

does that make sense??

What size cooler and was it a Trust / grex one? Do you have pics? The instuctions I got with the cooler shows installing it in left inner fender. USELESS!

I must be the only one with a 32 GTR who installed my oil cooler in front of BOVS....special. It can be done.

19 row oil cooler kit from UAS, earls fittings etc. Tight fit near one of the BOVS but the reason mine fitted was that I had previously removed the BOV piping. Also made brackets from aluminum to mount cooler.

That's great. Thanks for the pictures.

I purchased the Trust / Grex unit because it's of high quality and I prefered a vehicle specific kit rather than making brackets and having hoses made up for a universal kit. That's why I paid the extra money for it. But it seems unlikely this kit can fit in the intended location without changing BOV's or stuffing around. Not happy. I was assured this unit will fit without any modifications from the supplier, whitch I have in writing.

Some pics of my setup:

post-12712-1165636449.jpgpost-12712-1165636523.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...