Jump to content
SAU Community

In Need Of A Gtr Bonnet

Sarumatix

By Sarumatix,
in Victoria

 Share

Recommended Posts

Sarumatix Veteran

Sarumatix

Posted
Posted

I need of a GTR bonnet in vic, my car is currently under the hammer and the shop decided that the damage to my bonnet was pretty much unfixable (stoopid CF bonnets) so i'm in need of a new one.. pref a GTR one :happy:. Anyone know any places that might have one?

Link to comment
https://www.sau.com.au/forums/topic/146500-in-need-of-a-gtr-bonnet/
Share on other sites
700HP-GTR33 Mentor

700HP-GTR33

Posted
Posted
Yeah there are a few up north :miner: sadly I need one pretty soon and further more i'm already getting the money sucked outta me :laugh: not sure I can fork out over 1000 :S.

Either a Carbon-fibre or good condition Aluminium Bonnet $1000 is about the right price.

You may be able to call Nissan....seeing they have the R32 Parts in stock....

Hope I have been of some help.

:)

Ronin 09 Grand Master

Ronin 09

Posted
Posted

fark that Tekin, Beer Baron had a very good genuine alu one for around $600... I bought one off Bu5ter for $550ish.

$1K will almost get you a new Nissan bonnet.

No offence, but I think you need to get your facts straight before you give incorrect advice (which it seems you do alot of!)

Sarumatix Veteran

Sarumatix

Posted
  • Author
Posted

Bonnet is in quite good nick.. slight tear in the fibre though :/. I wouldn't be surprised if that would be bannable although i'm told it would be fixable. Can try and dig up a photo for you.

Yeah I been looking at around 600 for a bonnet but nothing in Victoria lately otherwise I would have snapped it up. Couple of offers from interstate but postage is a nightmare. Cheers for assistance guys.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • GTSBoy
      RB25 Drama's

      By GTSBoy · Posted

      Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      also possibly backed up to my filler and shat down it! 🤣
    • Julsmadrid
      RB25 Drama's

      By Julsmadrid · Posted

      Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...