Jump to content
SAU Community

Recommended Posts

good day,

i would like to get some advice.

I have a cefiro which i just put on the r32 gtr front brakes, now i have bleed all the lines several times and i am not getting any brakes, the peddle is soft real soft, i even took of the r32 callipers and press them in and put them back and mashed the peddle they work so its not that, i have used about 2 tins in brake fluid to bleed the lines i even replaced the rubbers in the master cylinder and still there is no brakes, not seeing any visible leaks, and i did not have this problem before i changed the brakes, the only issue i had sometimes was the peddle being hard which indicates a bad booster. so i am thinking it might be the booster so i got one from a r33 did not hook it up as yet, another thing i noticed was that when the car is off and u pump the brakes it gets hard and as soon as u start the car it goes soft all the way down to the flooring.

any ideas as 2 what might be causing this problem

thanks

Link to comment
https://www.sau.com.au/forums/topic/147100-r32-breaks/
Share on other sites

  • Replies 49
  • Created
  • Last Reply

Top Posters In This Topic

yeah i got the disc to go with the callipers, i did not upgrade the master cylinder, i only changed the rubbers in it as everything else looked fine, i have the r33 cylinder which i could use i would just have to get the lines made for it to work, but my thing is why it was working before and when i put on the new brakes i getting this problem

i would check for leaks like u suggest

thanks

Link to comment
https://www.sau.com.au/forums/topic/147100-r32-breaks/#findComment-2745701
Share on other sites

Are the calipers on the correct side?

If you've got left and right mixed up, you can bleed them until the cows come home, and you'll never get any pedal pressure.

I'll second this (meaning when mixed up, the bleeders are on wrong side as in top/bottom of the caliper), I've seen someone do this, when they realised what they had done wrong it was rather humorous.

Link to comment
https://www.sau.com.au/forums/topic/147100-r32-breaks/#findComment-2746205
Share on other sites

have you pumped the brake pedal while the car is turned on?...does the pedal get hard then?

my feeling is like huddys which is the master cylinder is too small (not the booster) What car is it? ...was it a non turbo cefiro at all ?

or failing that try sky031 and skypy's ideas first as its probably easier.

Link to comment
https://www.sau.com.au/forums/topic/147100-r32-breaks/#findComment-2746597
Share on other sites

Had the same trouble with my Ceff, put the R33 N/A front rotors on, then the R32 turbo calipers connected them all up then tried to bleed the system and found that no matter what i did there was no brake pedal so to speak.

I have also found that the std brake lines are not the correct fitting for the R32 calipers (they use a banjo bolt, R32s do not) and that the std brake lines were slightly too short on full steering lock.

im assuming that the R32 calipers have a marking on them indicating which side they go on, i dont see how having the calipers on the wrong side would affect braking so much...

Link to comment
https://www.sau.com.au/forums/topic/147100-r32-breaks/#findComment-2747067
Share on other sites

Well, assuming you have bled the brakes properly, and their are no leaks, id say its your master cylinder, because the gtr cyl and booster would be different to the standard one you have currently in the car in regards to the amount of fluid being displaced in the cylinder. I figure since you upgrading your brakes to be bigger you should upgrade the master cylinder to be bigger.

But thats just a suggestion, im possibly wrong on this one.

Link to comment
https://www.sau.com.au/forums/topic/147100-r32-breaks/#findComment-2747872
Share on other sites

Sky031 - how would you know which is the left and right side? does the nipple have a correct spot in that it should be on top vs the bottom of the calliper, like what Skypy12 suggested?

Huddy - i would try to get the 32gtst set up to see if it helps.

Resin - its a A31 non turbo cefiro, i am upgrading the car piece by piece, getting everything ready for when i go rb25det,

Ceffy SA - its the same problem that u had, how did u fix it? yeah the lines are different so i changed them to match the r32 callipers. but how did u get rid of your brake problem?

Gtrchick - i think you are right, i would upgrade the booster and master cylinder

dangerous daveo - no i did not get them rebuilt as they looked like they were in good condition.

Thanks for all the suggestions, i would try them till i solve my problem as i like how the brakes look on the car and there is no way i going back to the stock callipers and rotors

Edited by who's next
Link to comment
https://www.sau.com.au/forums/topic/147100-r32-breaks/#findComment-2748365
Share on other sites

Sky031 - how would you know which is the left and right side? does the nipple have a correct spot in that it should be on top vs the bottom of the calliper, like what Skypy12 suggested?

Below should shed some light on this....

The booster will change the amount of effort that goes into the pedal(Smaller booster = harder pedal and vice versa). But if you have a soft pedal and you can pump it upto being hard then your problem I would have said it's your master cylinder(or there is air in the lines somewhere). The turbo and non turbos skylines use masters with a different sized bore (gtst stock is 1")

check the side of your masters for the part nubmers to work out bore size

BM44 is 15/16

BM50 is 1"

BM57 is 1 1/16"

Youd want BM44 minimum but preferably BM50.

thinking about it more if it was the master you would just get a long pedal. meh too tired to think straight.

went to buy a z32 master cylinder it's different. The A31 has 3 brake lines comming from it and the Z32 has only 2 its a BM57
For starters, make sure you have the calipers on the correct sides (bleeder at the top of the caliper) I've seen it done before and you get a very long/shitty pedal as you can never get all the air out. Thats just one thing to check before you start spending cash, as we all have our blonde moments and do stupid things.

Next go grab yourself some of those plastic brake hose clamps to diagnose the problem. Clamp off all 4 lines. The pedal should feel normal.

so check that first before proceeding

The a31 master will have 2 lines for the front brakes whare as the z32 will have the single line which will be split into 2 at a junction box. You can get around this by installing a junction box but will require altering your brake lines. Then you can take both fronts off theck the then both rears ect you get the picture

Then if it is the master and you really cant find one to suit go get your master bored out if you end up having no luck, but abit of a pricey option. But surely there is another master out there to suit.

A 4 piston caliper will normally have more surface area to move under brake pressure so the brake pedal will have to travel further to overcome knockoff and make contact. No surprise it is soft. A larger master cylinder bore size should make it better. This is why brake mods are best left to the pro's, or at least get the right advice. You could completely unbalance the braking effort from end to end causing a major loss of control.

The common misconception that 4 piston calipers will magically give better braking with nothing else done is cause for real concern.

Edited by skypy12
Link to comment
https://www.sau.com.au/forums/topic/147100-r32-breaks/#findComment-2748458
Share on other sites

ok ill put my 2 cents in since i have a NA cefiro with a GTSt 5lug and brake swap....

i had the same issue... My reason was my MS was clogged and needed a rebuild...

the NA cefiro has a stock S13 size MS this will clamp the brakes with enough pressure to lock them (had to use the stock cause my GTSt MS was bad) but if you like super hard pedal then you should change it... note: a Z32 cylinder works also... u need the cylinder with two outlets for the front and one for the back... so good rule of thumb when looking for a new one.. oh and make sure you get a RHD cylinder haha i know how tempting those cheap z32 cylinders are on ebay haha...

and a smarty remark... you can bleed brakes with only one person if you have one of these

B000GBNE7Y.01-AO31J4X228FVG._SS500_SCLZZZZZZZ_V65367720_.jpg

Edited by 4DoorWhore
Link to comment
https://www.sau.com.au/forums/topic/147100-r32-breaks/#findComment-2748545
Share on other sites

I didnt fix the problem in the end, my brake upgrade is still sitting in the garage, im going to get custom brake lines made up to size from someone like enzed to be on the safe side, and yea i had someone helping me bleed the brakes to no avail.

Link to comment
https://www.sau.com.au/forums/topic/147100-r32-breaks/#findComment-2748881
Share on other sites

Good work skypy...

For starters, make sure you have the calipers on the correct sides (bleeder at the top of the caliper) I've seen it done before and you get a very long/shitty pedal as you can never get all the air out. Thats just one thing to check before you start spending cash, as we all have our blonde moments and do stupid things.

Thanks for finding that, it saved me a trip to the shed, and it's going to be about 48° out there under that tin roof at the moment. :dry:

They will fit on OK, they will appear to be bleeding fine, but unless the bleeder is at the top, you'll never get any pedal pressure.

Link to comment
https://www.sau.com.au/forums/topic/147100-r32-breaks/#findComment-2749826
Share on other sites

As has been suggested before, bleed nipples need to be at the top of the calliper.

They will work with the standard master cylinder, but you will loose alot of pedal travel (feels similar to air in the lines). Feels alot better if you upgrade to R32 master cylinder.

If you use the R32 banjo bolts and flexible hoses with your R32 callipers, you can connect them to the S13/A31 solid line where it enters the wheel arch, which means no modifications to fittings etc.

Maltech make ADR approved braided lines (they also do cheaper rubber lines), they are very professional.

I find it quicker and easier to bleed my brakes by myself. I've bled them the proper way with 2 people before, and it doesn't seem to make a difference. I don't use a fancy kit, just some clear rubber hose and a small clear container.

Edited by daisu
Link to comment
https://www.sau.com.au/forums/topic/147100-r32-breaks/#findComment-2750651
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...