Jump to content
SAU Community

Recommended Posts

yeh i removed mine 12months ago and have not had a problem,but that dont mean shit,just leave it in and wait till ya get cash for new turbos,or risk blowing them or ya motor or both in a worst case senario....

my2c

yeh i removed mine 12months ago and have not had a problem,but that dont mean shit,just leave it in and wait till ya get cash for new turbos,or risk blowing them or ya motor or both in a worst case senario....

my2c

do r34 GTRs have decent turbo;s meaning should be ok for him to run about 13 psi?

This thread is pointless. R34's do not have a boost restrictor. They have a marking where a restictor would be but they do not have a restrictor like the older GTRs.

As Geoff has already mentioned - R34 turbos are ceramic wheels with ball bearings. Mine was running 1 bar from the factory after I put a cat back + hiflow cat on it. They do this all day long and will go the distance.

If you want to pull a restriction out open up your airbox and check to see if you still have the factory plug in the wheel well intake hole. Pull that plug out and go for a drive. Sounds good :P

This thread is pointless. R34's do not have a boost restrictor. They have a marking where a restictor would be but they do not have a restrictor like the older GTRs.

As Geoff has already mentioned - R34 turbos are ceramic wheels with ball bearings. Mine was running 1 bar from the factory after I put a cat back + hiflow cat on it. They do this all day long and will go the distance.

If you want to pull a restriction out open up your airbox and check to see if you still have the factory plug in the wheel well intake hole. Pull that plug out and go for a drive. Sounds good :P

What he said is all correct but if a turbo lets go you risk sucking back the dust in the engine just like all other RB26's .

are you sure? I know the gtt has but according to HPI mag,the GTR 34 have steel.

I think they would have been refering to the Nur Edition (VSpec and MSpec), it had the steel wheel turbos (N1 spec), and they were the last of the R34 GTRs that were made. They also got other N1 component to make up the engine.

I think they would have been refering to the Nur Edition (VSpec and MSpec), it had the steel wheel turbos (N1 spec), and they were the last of the R34 GTRs that were made. They also got other N1 component to make up the engine.

When I was changing the actuator I had a closer look at the turbos, There are the same as what they had in the picture, 0.53 inlet housing?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...