Jump to content
SAU Community

Boost Restrictor In Gtr

andz

By andz,
in Engines & Forced Induction

 Share

Recommended Posts

gun32gtr Grand Master

gun32gtr

Posted
Posted

yeh i removed mine 12months ago and have not had a problem,but that dont mean shit,just leave it in and wait till ya get cash for new turbos,or risk blowing them or ya motor or both in a worst case senario....

my2c

DVS JEZ Grand Master

DVS JEZ

Posted
Posted
yeh i removed mine 12months ago and have not had a problem,but that dont mean shit,just leave it in and wait till ya get cash for new turbos,or risk blowing them or ya motor or both in a worst case senario....

my2c

do r34 GTRs have decent turbo;s meaning should be ok for him to run about 13 psi?

sewid Grand Master

sewid

Posted
Posted

This thread is pointless. R34's do not have a boost restrictor. They have a marking where a restictor would be but they do not have a restrictor like the older GTRs.

As Geoff has already mentioned - R34 turbos are ceramic wheels with ball bearings. Mine was running 1 bar from the factory after I put a cat back + hiflow cat on it. They do this all day long and will go the distance.

If you want to pull a restriction out open up your airbox and check to see if you still have the factory plug in the wheel well intake hole. Pull that plug out and go for a drive. Sounds good :P

wrxhoon Grand Master

wrxhoon

Posted
Posted
This thread is pointless. R34's do not have a boost restrictor. They have a marking where a restictor would be but they do not have a restrictor like the older GTRs.

As Geoff has already mentioned - R34 turbos are ceramic wheels with ball bearings. Mine was running 1 bar from the factory after I put a cat back + hiflow cat on it. They do this all day long and will go the distance.

If you want to pull a restriction out open up your airbox and check to see if you still have the factory plug in the wheel well intake hole. Pull that plug out and go for a drive. Sounds good :P

What he said is all correct but if a turbo lets go you risk sucking back the dust in the engine just like all other RB26's .

VSPEC-33 Community Regular

VSPEC-33

Posted
Posted
are you sure? I know the gtt has but according to HPI mag,the GTR 34 have steel.

I think they would have been refering to the Nur Edition (VSpec and MSpec), it had the steel wheel turbos (N1 spec), and they were the last of the R34 GTRs that were made. They also got other N1 component to make up the engine.

Baysidebluebnr34 Rising Star

Baysidebluebnr34

Posted
Posted
I think they would have been refering to the Nur Edition (VSpec and MSpec), it had the steel wheel turbos (N1 spec), and they were the last of the R34 GTRs that were made. They also got other N1 component to make up the engine.

When I was changing the actuator I had a closer look at the turbos, There are the same as what they had in the picture, 0.53 inlet housing?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • LaurelPWR
      Forced Performance Hta Turbos

      By LaurelPWR · Posted

      Dredgggggeeee time; I have recently finally started driving the car. It sat for so long that the fuel tank gave birth to rust sludge and blocked my lift pump sock and one of my walbro 460's and left grime, rust chunks and muck all through the surge tank and system. I decided to commit and pull the trigger on an oem r32 gtr fuel tank and Frenchys twin 460 / sender / surge tank hanger combo and all new larger lines and fittings etc, also boost doc heater hose kit / new heater core and a heap of other bits and shits like wideband sensor installed in the dump and Syltech iacv + lines and all wired and added to current tune. now having lightly driven it a couple times without issue, I can happily report on the hta3076 in its current tune. still no boost control switched on, 20psi gate springs, car makes 22psi at 3200rpm in 6th gear with 30-50% TPS from cruise at 100kmh. Going by the old graph, this means it should be making 300-325whp at the same numbers above. Very very responsive setup under true road driving loads. all that's left for the build is body loom + PDM, finish the remote aircon setup, install carbon fibre parts and go for full tune and 30psi. the 315 rear tyres are now performing like they're 195's, wheel spin in any gear at almost any rpm, whereas my previous setup hooked up in 3rd no issue, albeit Nt01's back then / RB25 5spd vs (new) old date r888r's Z34 6spd now, + obviously all the support upgrades I listed in the quoted post above. car sits at 1-3psi on cruise at 100kmh, expectations totally exceeded and I'm beyond stoked with all this so far. IMG_4848.mov
    • Shizu
      Sheraaz's R34GTT Build

      By Shizu · Posted

      Thanks mate.
    • TurboTapin
      Crank Motorsports Front Axles

      By TurboTapin · Posted

      I've also been eyeing their rear axles for my car. I purchased seat mounts from them about 7 years ago and they were hot garbage so I've been a little wary about purchasing them. With that being said, please buy them and get back to us haha. 
    • Shizu
      Sheraaz's R34GTT Build

      By Shizu · Posted

      Can a moderator please move this into the right category.. I've accidently put this into racing build thread 🤦🏽‍♂️
    • Shizu
      Sheraaz's R34GTT Build

      By Shizu · Posted

      Being a manual, we very quickly ordered new R34 gearbox (From Nissan) and remaining parts from Kudos motorsports. Would highly recommend the team there. Ultra helpful and quick to share advice and upgrades. We are in the middle of taking the Auto out (Genuine 94,000/kms) and putting the Manual in this weekend. Part 2 of the build will include likely a Plazaman Intercooler and Plenium, Hks Exhaust with Tomei Dump (ordered).
×
×
  • Create New...