Jump to content
SAU Community

Recommended Posts

bleh, sif it makes a difference, i have a friend who's father has a 700odd hp twin turbo v8 supra using a just jap intercooler, runs fine no worries.

Its all marketing hype, admitadely, $2000+ inter cooler kits fit better and thats about it.

cheers

I've got one, but haven't installed yet... don't know if i will either. The only time I give my car stik is at night and the air is cool enough already.

The highest knock level I have had at night has been 17 which is nothing. However if you're stupid and crusify your car during a hot day it would benefit your cause a little.

If your car is completly stock the intercooler will make it slower due to the extra meter of piping and the huge volume of the intercooler that has to be filled with boost.

A FMIC will make your car look faster, besides that at this level of performance any el-cheapo or brand name cooler will cool effectively enough for your needs. So yes, they work good.

Which cooler is it? bar and plate or tube and fin? Either way though i've seen these coolers support in excess of 260rwkw so they can't be bad...alot of brand snobs would say otherwise but results speak for themselves...and its usually the piping that lets you down...cheers...

Which cooler is it? bar and plate or tube and fin? Either way though i've seen these coolers support in excess of 260rwkw so they can't be bad...alot of brand snobs would say otherwise but results speak for themselves...and its usually the piping that lets you down...cheers...

I bought a hybrid copy kit that came with a delta fin core, its basically a APEXI intercooler copy.

The isntall was not exactly a easy botl on but its all together is fairly good. I f could do it agian i would have saved the money and bought the blitz style that uses the stock IC pipes off the turbo and in the intake. I personally dont liek the ider of the hybirs kit with a pipe running across inbetween my radiator and engine then having to cut my fan blades not to mention make a 3inch hoel in the side of the car for the pipe.

Other wise for the money great kit. I have the Bar and plate before and apparently the Delta fin is supposed to be better and cost more. Ohnestly for a street car under 150 rWK i doubt id notice the difference?

  • 5 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
×
×
  • Create New...