Jump to content
SAU Community

Recommended Posts

Hi People,

I had a bearing failure and as a result had metal go through my engine. The engine is now rebuilt and I was womdering if I should replace the oil cooler before running it again. Some people have said that no matter how much you flush em that some metal could remain inside em and potentially enter your engine later. Also the engine builder suggests not running the oil cooler during run in. What do ya's think?

Link to comment
https://www.sau.com.au/forums/topic/148199-should-oil-cooler-be-replaced/
Share on other sites

Look, if you are that worried about it, just buy a new cooler. They are not that expensive if you just pruchase the ehat exchanger. make sure you correctly identify the fittings before you order it. Try the PWR stuff.

As for not running it during run in, well it probably wouldn't hurt to do what the man says.

"Look, if you are that worried about it, just buy a new cooler. They are not that expensive if you just pruchase the ehat exchanger. make sure you correctly identify the fittings before you order it."

thats exactly right. and for the risk of what. $300. Why not buy it so feel 100% confident in your car next time you drive it

i reckon, flush with water, then air, then water, then vacume, then do again, just to be safe. the water should carry it,, air should blast it out, or vacume reverse, should be cleaned out right?

if u dont take the chance, ill have it, pm me,

Edited by silverbulletR33

This is a little bit off the topic of the cooler being replaced, but wanted to say a few things in regards to oil coolers themselves. Probably the biggest oversight with oil coolers is the actual need for them (I sell them, so this is not a sale ploy, but rather sincere advice). I don't want to insult your intelligence so if this is common sense to you just ignore it.

All oils have a certain operating temperature in which the oil performs at its best. Oil coolers not setup with a thermostat can alter the oil temperature levels which can delay the oil getting and staying at the optimum level. Therefore before any oil cooler is actually put into the system buy a quality oil temp gauge and determine the sort of driving you do and the effect on the oil temp it has. As most people's oil will not go beyond the range specified by the manufacturer. Then, and only then, look at buying an oil cooler kit. And as previous posts have eluded to buying a quality oil cooler is the safer option as cheaper Asian copy runs the risk of poor manufacturing and disintegrating into your engine.

This is purely my opinion, therefore take from it what you will. However I strongly believe that oil coolers are a very misguided modification that people make in order to look good, without ever thinking of the affects it will produce.

This is a little bit off the topic of the cooler being replaced, but wanted to say a few things in regards to oil coolers themselves. Probably the biggest oversight with oil coolers is the actual need for them (I sell them, so this is not a sale ploy, but rather sincere advice). I don't want to insult your intelligence so if this is common sense to you just ignore it.

All oils have a certain operating temperature in which the oil performs at its best. Oil coolers not setup with a thermostat can alter the oil temperature levels which can delay the oil getting and staying at the optimum level. Therefore before any oil cooler is actually put into the system buy a quality oil temp gauge and determine the sort of driving you do and the effect on the oil temp it has. As most people's oil will not go beyond the range specified by the manufacturer. Then, and only then, look at buying an oil cooler kit. And as previous posts have eluded to buying a quality oil cooler is the safer option as cheaper Asian copy runs the risk of poor manufacturing and disintegrating into your engine.

This is purely my opinion, therefore take from it what you will. However I strongly believe that oil coolers are a very misguided modification that people make in order to look good, without ever thinking of the affects it will produce.

What you have said there is spot on the money. Getting a cooler without a thermostat certainly does make the oil take longer to get up to temp.

In relation to poor quality components, I would like to make a correction in that Asian parts are often stereotyped as being of poor quality. Asians love to reverse engineer stuff (take it apart), learn from it and copy it. As they have very cheap labour there, they can make very high quality components.

Parts made by bogans are of no better quality. As I have often seen, aussie stuff is often overpriced, and of a poor quality. Take holden adn ford as an example. I have owned both, and have had nothing but trouble. After my dad bought a toyato camry, I vouched never to buy a holden or ford again.

Yes I agree there is a certain stigma attached to parts that come from Asia. And although there are some very good stuff that is reasonably priced, a lot of it however has very poor quality control mechanisms in place, and manufacturing processes are not standardised. The debate will go on as to what is best value for money, but as with any critical engine component things like warranty, workmanship, integrity and precision all have to weighed up. Just don't fall into the trap of going the cheapest, as doing a job right the first time will be far cheaper than doing a dodgy job a few times.

Take it to an engine reconditioners for an acid dip/clean. Would be lucky to be $30.

When you see how much material remains in a block after machining and honing you would be worried about the remains, but for an extra $70 my reco shop does a full pre build clean and bags the block and it is spotless.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...