Jump to content
SAU Community

Recommended Posts

my current ride , the 33 gtr is sweet . but im thinking of building a purpose built drifter .

what model would be best suited ?

s13 - either get an old na shitter and do it up or a fairly nice 91+ SR20 with potential

cefiro - great drifter but a bit hard to find now the 15 year rule is all stupid . 4 doors would be cool

r32 or r33 - either sedan or coupe . would prefer sedan for something a bit different (atleast the 33 sedan is not common for drift) , would probably prefer 33 due to better engine and box but i think the 32 chassie would be a bit nibler for drifting

s15 - the last and most expensive option . probably not going to happen but would be nice

any thoughts would be appreciated

Link to comment
https://www.sau.com.au/forums/topic/148711-best-drifter/
Share on other sites

its really each to their own and what your comfortable with. Obviously an s13 based drifter is best for 'drift physics' however, just say you've driven a 33 for a while now and your used to catching that sort of base in oversteer then that's probably what your going to be better at. I drove a mates S15 today and found it was a HELL of a lot harder to go from my car (R33) to his S15. totally different feel and mannerisms. go with what suits you. BUT if you dont give a shit and wanna learn something new then definetly S13 cheap and easy.

Link to comment
https://www.sau.com.au/forums/topic/148711-best-drifter/#findComment-2779791
Share on other sites

are r34 engines good for drifting, i heard they can stuff up (oil pressure or something)??

i was thinking of taking my car to a practise night in the new year & just wondering what precautions i will need.

cheers

steve

Link to comment
https://www.sau.com.au/forums/topic/148711-best-drifter/#findComment-2779811
Share on other sites

im pretty sure you wont have a problem. oil swishing around your sump is a major issue for all motors without a dry sump setup. I'm unsure if you can get those winged sumps like the SR's have. but yea oil splish splash is a no no for all motors, whether it be drift OR drag. other than that you could sit that thing on the limiter all day long and she'll be fine. just make sure you got all your fluids to the correct level. I wouldn't take a motor out thrashing without a fmic. that's a definate.

Link to comment
https://www.sau.com.au/forums/topic/148711-best-drifter/#findComment-2779815
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...