Jump to content
SAU Community

Recommended Posts

Anyone know of a car storage place in Perth NOR?

Most places I've rung have no vacancies and are expensive.

Been looking after my Brother in Laws WRX for 2 years while he works away and want my garage space back.

Alternatively anyone want a '03 WRX (red) with 24,000kms for $30k?

I think he should sell it personally but yards didn't offer enough.

Link to comment
https://www.sau.com.au/forums/topic/150082-car-storage/
Share on other sites

Why not just take it to a storage place? My work uses a storage area in subiaco with a lockable garage door (easily enough room to fit a car) and I dont thinnk it is all that expensive. We keep 40-50k worth of stock there so a 30k car shouldn;t be an issue???

There is a storage place in Joondalup near Toys R Us, one just near the Hutton St exit on the mitchell fwy... pleanty of these places around.

Link to comment
https://www.sau.com.au/forums/topic/150082-car-storage/#findComment-2797866
Share on other sites

Why not just take it to a storage place? My work uses a storage area in subiaco with a lockable garage door (easily enough room to fit a car) and I dont thinnk it is all that expensive. We keep 40-50k worth of stock there so a 30k car shouldn;t be an issue???

There is a storage place in Joondalup near Toys R Us, one just near the Hutton St exit on the mitchell fwy... pleanty of these places around.

The one in Joondalup is $340 per month and have been on a waiting list for 3 months there

Link to comment
https://www.sau.com.au/forums/topic/150082-car-storage/#findComment-2804365
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...