Jump to content
SAU Community

Recommended Posts

oh i thought it said that it was a repairable write off.

Must be seeing things....

do you guy think that its worth buying any damaged car and repairing it?

I mean a car with less damage obviously.

I'm going to keep searching for slightly damaged cars and hope i can get a bargain (and not a lemon).

if u really want to do something like that, why not send it to thailand/indonesia it will cost u lot less in labour charges. eg u r living in NZ, get a wreck/damaged from Japan, but send it to Thailand/Indonesia/or even japan etc to get the damage repaired. keep in NZ for the rest of 1 year, and then bring it in as a Personal import. perfect (well for u, not someone who buys it off you)

Bec: if it was not too damaged i would be doing most of the work myself (i want to learn how to fix a car etc.)

Fuzzy scuz: I wouldn't mind doing that but I dont think many people would be looking for brand new rex parts out of this model (or am i thinking wrong??)

Ziad: I'd prefer fixing the car myself to learn the car etc. and to learn the basics about cars in general.

If i find another car (without any structural damage) i will post up and everyone can give me their opinion.

Thanks for all your help

Bec: if it was not too damaged i would be doing most of the work myself (i want to learn how to fix a car etc.)

Fuzzy scuz: I wouldn't mind doing that but I dont think many people would be looking for brand new rex parts out of this model (or am i thinking wrong??)

Ziad: I'd prefer fixing the car myself to learn the car etc. and to learn the basics about cars in general.

If i find another car (without any structural damage) i will post up and everyone can give me their opinion.

Thanks for all your help

You are choosing the wrong type of damaged cars to learn with :huh:.

This is waaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaay beyond a beginner's level for repair. Hell some people that have been in the trade for 10yrs may find this project a task and a half to complete properly.

You need to find something with very minor accident damage :P

You should probably start on a slightly damaged Silvia, with mild panel damage, maybe a pushed-in radiator support. This way parts are cheap and it wouldn't be too hard to fix.

Even then, you would at least need to know how to weld. Trust me, having fixed two damaged cars already, it's never worth it in the end.

Unless you can get all the parts you need cheap or free, then don't bother with expensive cars, or it will prove to be a very expensive lesson.

I'm on my third repair now and just can't be bothered. Alligning guards, bonnets, cutting, straightening, it's just a pain. Hence, I've just taken my car to the panel beaters this time.

With regards to switching plates, it's not that easy. If the car was declared a write-off, it will need to get a VIV certificate before it can be re-registered. They are used to dealing with all the Habib's from Broady, so they know exactly what to look for. They thoroughly check that the numbers are legitimate and not swapped over, ensure you have receipts for parts and that panel work was actually completed.

Anyway, good look with your endeavours.

Yeah, not an amateurs repair by any means.

Also, with that much damage, gearbox casings could be damaged/split. all sorts of stuff that you visually cant see until you pull all the parts out.

Suddenly a cheap wreck your trying to sell parts from, isnt worth anything as the parts themselves are damaged to a point of no return

I didn't mean that i would be using this car to learn how to repair with, but i meant that i wanted to learn how to repair cars etc., by repairing one to start off with.

If a slightly damaged silvia would be the way to go, anyone have one or know who has one for sale???

I know someone in the industry that could help me out, and get me cheaper parts.

:laugh:

So you where going to buy this car, keep it in storage for a few years, till you have gained enough experience to repair it?

In you first post you stated:

Was looking at getting this car and repairing it.

Do you guys think it would be worth it?

I'm looking to get a cheap car, and i was thinking that i could get a newer car that was damaged and i could repair it, thus making it cheaper than if i was to buy it in good condition.

Then above you stated:

I'd prefer fixing the car myself to learn the car etc. and to learn the basics about cars in general.

Which tells me you wanted to learn how to fix cars using this wreck.

Best way to learn would be through an apprenticeship. Then start off small and cheap, something like a datto, rx3, silvia, etc

AL:

I said that i wanted to buy this car, repair it, and by repairing it, i would learn some of the basics about cars etc.

I in no way said that i would be buying the car, keeping it in storage and then repairing it once i had gained enough experience

My previous post was in reply to this.

I didn't mean that i would be using this car to learn how to repair with, but i meant that i wanted to learn how to repair cars etc., by repairing one to start off with.

I am merely stating that there is nothing basic about repairing this car.

To learn the basics you need to start with basic accident damage, not write-offs, involving highly technical cars.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...